Question about Kenmore 22422 Top Load Washer

1 Answer

Kenmore Elite Oasis HE/ Error Code F1

Upon Starting the washer it locks the door and starts, then The F1 Starts flashing and the washer stops. IF I stop it and start it really quick by the third try It will run through it's cycle. Help this has been an ongoing problem since I bought this machine. I am really frustrated with this.

Posted by on

  • 8 more comments 
  • Anonymous Aug 12, 2008

    Yes, I have the same F1 code error on washer purchased in 2007. Help! Mine is 26 27086

  • drea7467 Sep 13, 2008

    I have the EXACT same problem, I am so disappointed in my purchase! I do not recommend this product, and have not fixed it. I too, press stop and start 3 times and it works- Kenmore has really gone to the dogs over the years. Maytag next time.

  • tpeila Sep 27, 2008

    I have the same problem. Bought washer and dryer set last year. Sometimes mid cycle on the dryer I get an error 41 cdoe too and it just stops drying. New brand next time! ARGH!

  • ljcljc Nov 03, 2008

    I have the Kenmore Elite Oasis also and recieved the F-1 code when it was not quite two years old. It cost almost $400 to fix it---control panel was faulty. Sears will not stand behind it, although based on what I'm reading on the internet, it's a very common problem. I am so disappointed in this machine and will never buy anything from Sears again.

  • drea7467 Nov 04, 2008

    My non-washer is a Kenmore Elite Oasis HE mod 110 27087604 type 580 ser cu0270410 with of course the F1 error, now raking in 5 or more errors before FINALLY starting the washing load, and again during rinse cycles...so frustrating. So much for trying to have something nice after losing everything during Hurricane Katrina....may give SEARS one more try this week-we'll see.

  • Anonymous Nov 17, 2008

    I have the exact same problem (F1)with my Kenmore Elite Oasis Canyon Capacity washer. I start/stop 3 times then it works. It's very frustrating. It also has a very loud sound when spinning.The repairman from Sears ($75 visit) was on the phone the entire visit. He finally said he would need to replace board and tub/with bearings for a total of $573.87 to fix a 2 year old $1,100 machine. Of course I sent him away still frustrated with Sears not standing behind their product. And to think I was actually going to buy a matching dyer soon. No way!

  • chrisstoj Nov 19, 2008

    I have been having the same F1 code error problem since I purchase my washer and dryer set over 2 years ago. This is now the 4th time I am having them come out and fix it. How do I go about getting them to replace my washer? or will they do that? I am really getting tired of not being able to wash clothes for 2-3 weeks while I am waiting for a part to come in. I paid a lot of money for the set and was so excited to get a black washer and dryer set to match the rest of my applien. in my home, now I am just frustrated but I can not afford to buy a brand new set right now or even in the near future. Once I get a F1 code on my machine it won't go through the cycle at all.

  • Anonymous Jan 29, 2009

    code F1 error and sears will not cover a known problem with their washer

    i would not recomend purchasing such a high ticket item........

    te company should stand behind their product....\\\\\\

  • Anonymous Feb 06, 2009

    I am having the same problen F1 beeps till I push stop/start then it will go this happens 4 times until it will start washing . Again at 17 seconds beeps two more times so I have to push stop/start . So unhappy with product

  • Anonymous Mar 07, 2009

    I have the same problem with saved error codes of 51 and 68. The diagnostic guide says that this is a "primary control failure. Replace the machine/motor control assembly."

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 261 Answers

Ok these are not the series 70, getting a model number off the door will reallllllly help. Some of these sound like the oasis. F1 is motor control or primary control failure and F 41 is a rps thermistor failure.
For the guest with the 11027086601 kenmore elite oasis here is a link for supplying me with a partial model number, much thank yous!! paste in a browser:)

http://www.searspartsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?modelNumber=11027086601&productCategoryId=0153200&brandId=0583&modelName=RESIDENTIAL WASHER&diagramPageId=00002&componentDescription=CONTROL PANEL PARTS&documentId=K0601003&backToLink=Return to Sub Components list

Posted on Nov 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is F1 failure code on a kenmoore oasis washer


check your owner manual section troubleshooting for error code very important.
Normally this error code can be meansL a) pressure out of range.
or b)eepron error.
or call the factory and get support online via chat or phone for to fix it.
God bless you

Sep 25, 2012 | Kenmore 4.7 cu. ft. High-Efficiency Top...

1 Answer

My kenmore oasis shows the f1 upon starting the machine and at 23 minutes and often shows th ul why is this


Mine is doing the same exact thing. Just after I press "Start", the F1 starts beeping. Then at 23 minutes into the cycle, it does it again. So frustrating! What is wrong with this machine?

May 20, 2010 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

F1 error


yep electronis control board in the console is bad.

Apr 26, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Kenmore Oasis HE Canyon Capacity F1 code?


The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question!!!!!

Apr 25, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

F1 code coming up on my Oasis HE washer


YES! Serious problem...more annoying than anything else. Wait until your machine stops at the spin cycle and displays "F1" again. We just had a repair tech out today and received a quote of $384+ to fix/replace the circuit board. Kenmore & Sears are fully aware of this problem and have issued a recall on a model that is one digit off of the model I have yet they will not do anything about this even though it is the same problem. These machines are huge dogs!

Jan 15, 2010 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Machine stops several times shows F1 code


this is a main control board failure and needs to be replaced

Sep 16, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Kenmore Elite Oasis Washer Error Code F1


per sears unplug the washer for at least 10 min then plug back in and push pause or stop 2 time.

Mar 25, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

F1 error code on Kenmore Oasis He


Moister can get in between the contacts,is it in a high moister environment? Try using a hair dryer on the panel to dry it out.Also unplug it to reset.
Hope this helped.Let me know by rating me
For more help go to live chat.
lenwest

Jan 31, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Kenmore Elite Oasis HE/ Error Code F1


Sorry to tell you but you have a faulty control board. It is a bad part from the factory. They know that its bad too! They have completely remanufactured the part. There is lawsuit against whirlpool (whirlpool made the oasis) for the problem. Some people have been able to call and complain to whirlpool and got them to pay for the repair. Complain a lot. Good luck. sorry for the bad news.

Nov 20, 2008 | Washing Machines

Not finding what you are looking for?
Kenmore 22422 Top Load Washer Logo

1,348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...