Question about Schwinn Meridian Adult 26-Inch 3-Wheel Bike

2 Answers

How do I remove the back wheel to replace it due to its bent up;I removed to the outside nut and wheel wont come off ?

Posted by on

  • 2 more comments 
  • lovecountry5 Mar 22, 2011

    I just received this answer of how to REMOVE the back wheels of a Schwinn Meridian trike bike, the answer is : Amazon is sold out try E-Bay ? Now thats an answer for an Idiot ? I can find the parts its HOW do you Remove the Back wheels ? I removed the outer Nut and the wheels wont budge. I dont want to beat them up and damage the axle.. whats the secret ? There is no secondary nut still holding it ? Thanks for what ever help you can send me..

  • lovecountry5 Mar 22, 2011

    Thank you for an intelligent answer and my problem was solved. I didnt have to remove the axle but knowing one wheel wasround and the other was half moon I was able to remove it without damage . Now I can order another wheel and be riding. I wasnt being a smart A__+ for the first guy but his answer of BUY It on E-Bay wasnt expert knowledge. The pictures helped quite a bit.. My Hats off to you !

  • lovecountry5 Mar 22, 2011

    I sent my Grats already to techs site.. Thanks !

  • Stephen Obester
    Stephen Obester Apr 22, 2017

    Is it a single axle for both wheels? I have a Schwinn 3 speed but it seems to have the drive axle and an independent assembly (left) or is the shaft broken?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,961 Answers

Hello!
You will need to remove the two bolts and nuts/washers that hold the wheel axel in place. After that you can pull the wheel off the frame with a little force. See the image below where two bolts that hold axel on both side are.
How do I remove the - alpug_42.jpg


The bolts are square near the end and will go into a square hole or cut out in the bikeframe. Putting these bolts on is a bit difficult at first, but once you have done it, its basically easy.

For the rear wheels, the right side axel is shaped like a "D" (not round) and will only take the corresponding wheel with the "D" axel area. The other rear wheel has only the special bearings for its axel and no "D" area.

Posted on Mar 22, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

I checked on Amazon, but they are out of stock. Try eBay or your local Schwinn dealer.

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 nissan sentra 1.6 idler pulley wont come off


Remove & replace the entire pulley assy.bracket & all

Buy from dealers parts dept

You do not need a gear puller

If you do, then you have a lot of damage to the brg, as you said,
& you replace every thing it attaches to ,as I said

You may have to drop the sub frame or raise the engine or
both, to get clearance

Aug 02, 2012 | Cars & Trucks

1 Answer

How to remove steering wheel


Disconnect battery,,,,,,,,remove screws from back of steering wheel cover.. front of steering wheel cover will come off and may be plugged into steering wheel carefully remove wire plug from tab.remove large nut on center of steering wheel , use puller kit from local auto parts store , prob wont come off on its own but might . BEFORE removal note location of scratch on wheel , matching scratch on post for alignment of wheel on replacement ,slide steering wheel into place, tighten nut just enough, replug wire and dont make screws too tight re hook battery and reprogram radio.... sorry.. yur welcome

Jan 13, 2012 | 1997 Acura CL

1 Answer

BENT THE RIGHT REAR AXLE ON MY 1996 FORD CONTOUR AND NEED TO KNOW HOW TO REPAIR IT


you don't repair it, you replace it. jack it up, remove the brakes, and all the brake assembly from that axle,, http://www.ehow.com/way_5731956_ford-rear-brake-replacement-instructions.html then remove the bearing cap,, cotter pin, and nut from the spindle , ( you might want to replace the wheel bearing at the same time due to the bad axle ) remove the axle bolts,, and shock bolts, from the axle beam. remove axle beam assembly

Sep 23, 2011 | 1996 Ford Contour

3 Answers

How to replace a front wheel hub assembly on a 1999 blazer 2wd


remove tire
remove axle nut
remove 3 bolts holding hub in
sometimes may need to hit hub with hammer after all bolts out to get it to release

Dec 22, 2010 | 1999 Chevrolet Blazer

1 Answer

Unable to remove wheels and replace with new ones. Need instruction booklet


cathjh7 what type of chair do you have? Are you talking about the drive wheels on the motors? Usually there is a bolt or nut in the center of ech wheel. On some chairs there is a lock washer with a bent tab keeping the bolt from getting loose. This tab must be bent down flat before you can remove the bolt. Once you have the bolt or nut removed pull up on the wheel and it should come off the axle. Now for the bad news---- if the wheels have not been removed in a long time and you have ridden through water or in wet grass the hub can get rusted to the axle and they are very difficult if not impossible to get off. I have had to use a tierod tool to get them off and I have had to replace the entire motor because I couldn't get the wheel off the axle. It might be best to see the provider you got the chair from for help with this problem. Hope this helps you

Sep 25, 2010 | Electric Health & Beauty

1 Answer

How to replace brake pads on 1998 ford mustang


break lug nuts loose
jack up car place stand under car
remove lug nuts and wheel
remove brake caliper
take out pad on outside of caliper
place a brake caliper press on pad next to piston of caliper and compress piston back in caliper
remove press and replace pads
reinstall caliper and wheels set car down
REMBER TO GET IN AND PUMP BRAKE PEDAL A COUPLE TIMES OR YOU WILL NOT HAVE ANY BRAKES WHEN YOU MOVE YOUR CAR!!!!!!
check fluid in master cylinder
take your time

Feb 25, 2010 | 1998 Ford Mustang

1 Answer

2002 ford explorer rear wheel bearing removal


Rear Wheel Bearing
REMOVAL AND INSTALLATION

1. Remove the wheel knuckle.

Wheel Knuckle
REMOVAL AND INSTALLATION

CAUTION: Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.

1. Remove the wheel and tire assembly.

NOTE: Have an assistant press the brake pedal to keep the axle from turning.

2. Remove the nut and washer and discard the nut.

3. Remove the parking brake shoes.

CAUTION: Do not damage the boot while separating the toe link from the knuckle.

4. Remove the nut and bolt and separate the toe link from the wheel knuckle and discard the nut.

CAUTION: Do not damage the boot while separating the ball joint from the knuckle.

5. Remove the nut and bolt and separate the upper ball joint from the wheel knuckle and discard the nut.

CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.

6. Using the special tool, press the outboard CV joint until it is loose from the hub.

7. Remove the nut and bolt and the wheel knuckle, hub and bearing as an assembly and discard the nut.

(Return to)
Rear Wheel Bearing
REMOVAL AND INSTALLATION

2. Remove the three bolts.

CAUTION: Make sure that the press adapter outside diameter is slightly smaller than the hub outside diameter or damage to the knuckle will result.

3. Using a suitable press, remove the hub from the bearing and discard the hub.

NOTE: The retainer ring is tapered and must be installed flat side down.

4. Remove and Discard the retainer ring.

5. Using a suitable press, remove the bearing from the wheel knuckle and discard the bearing.

CAUTION: The hub and bearing cannot be reused after disassembly.
To install, reverse the removal procedure.

Jan 24, 2010 | 2002 Ford Explorer

2 Answers

Locked up Eager 1 6.75 Craftsman Mower


The timing may be off due to a bent or broken flywheel key. See if you can remove the flywheel and look at the keyway. To remove the flywheel: take a nut with the same size threads as the one that holds the flywheel on. Thread it on but not so far as to let the shaft come through. With your weak hand, lift the flywheel with a little upward pressure. With the strong hand, tap the nut with a wooden mallot if you have one. If you dont, use a hammer. Tap the nut and the flywheel will come off. You may have to tap it sharply. Once you have done that, remove the nut and save it for another day. You will be able to see if that is the problem. Good luck...Lee

Sep 02, 2009 | Garden

2 Answers

Installing front brake pads on my 2006 F150


yes, The springs clip onto the pads on the ends, you can see how they would hook over. Pot you silicone on the the outside of the spring

Jul 24, 2009 | 2006 Ford F-150

1 Answer

Need to replace steering arm on pass side on 1998


Your description leads me to believe that the spindle is bent. This is the piece that the tie rod attaches to near the wheel. Sometimes the tie rod is attached to a piece that attaches to the spindle which is rather intuitive. Just remove the tie rod end, unbolt the arm that attaches to the spindle and replace the arm. In this case the only special tool you'll need is a tie rod seperator.

If the arm is a part of the spindle and cannot be removed easily:

1) Put vehicle in park and safety brake on - chock the rear wheels
2) Lift passenger side front wheel and put on jack stands
3) Remove wheel and have a friend apply brake pressure
4) Loosen hub nut with appropriate socket (22 to 35mm)
You can purchase the socket from your local auto parts store
You'll need a large breaker bar, its torqued to about 100ft-lbs
5) Remove tie rod end with a tie rod/ball joint separator
This can also be purchased at your local auto parts store.
Some spindles are made with tie rod end permanantly attached
If it is removable, remove nut and drive the separator tool
between the tie rod and spindle using a large hammer.
It'll eventually break free from the spindle.
6) Remove the strut with a strut spring compressor tool
WARNING - THIS IS VERY DANGEROUS
This can be purchased at your local auto parts store.
Compress spring before removing lower bolts (2 of them).
The strut may be left on vehicle but the spring must be
compressed.
7) Remove caliper and break assembly
Loosen the two slide bolts that go through the caliper assembly
Remove caliper and breaks - let it hang by the tubing
8) Detach upper and lower ball joints with seperator tool as in #5
9) Finally remove the hub nut from #4
The spindle should slide off the axle
10) Repair or replace the spindle and put it all back together in
reverse order using new wheel bearings. Pack them with axle
grease if theyr'e not the sealed type.

NOTE: The tie rod end may need to be replaced also. The vehicle will need a front end allignment. Be sure to torque the hub nut to the manufacturers specifications - at least 75ft-lbs. You should probably replace the wheel bearings.

Jan 02, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
Schwinn Meridian Adult 26-Inch 3-Wheel Bike Logo

Related Topics:

610 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schwinn Cycling Experts

Tony

Level 3 Expert

2600 Answers

michael
michael

Level 2 Expert

122 Answers

jasiel murphy

Level 2 Expert

94 Answers

Are you a Schwinn Cycling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...