Question about Penn Gt Series Levelwind Reels 330GTi

1 Answer

My penn 4300 ss, the bail won't close on it's own when I rotate the handle, I can close it manually. I have 3 other 4300's that work fine

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You need to either replace the bail spring or release any tension cause by the bail wire gap being too wide or to small. Take apart the bail wire and adjust the gap so that it doesn't bind when closing the bail.

Posted on Mar 27, 2011

  • Bill Walsh
    Bill Walsh Jun 18, 2014

    a little bit of lubrication would also help a whole lot. problem solve the problem

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the bail so that it closes when then handle is turned


normally that happens when the bail spring is broke .so you replace it .

May 25, 2016 | Fishing

1 Answer

Hatch won't close


you dont say which latch it is but check the part that latches on the stud sticking out. if its closed just pull open handle and manually flip the latch open an should work fine.

Oct 29, 2012 | 2011 Audi Q7

2 Answers

Pasta boat manual


MicrowavePasta Boat InstructionsFor elbow, bowtie, ziti, rotini, and penne

1 serving -1/2cup -water levelat #1
2 servings -1 cup -water level at #1
3 servings - 1 1/2cups - water level 2
4 servings - 2 cups - water level at 4
6 servings - 3 cups - water level at 6
8 servings - 4 cups - water level at 8

cook times based on serving ( serving - minutes)

1 - 17
2 - 18
3 - 21
4 - 23
6 - 25
8 - 27

Stir macaroni once halfway through cooking for al dente; for softer pasta, cookseveral minutes longer.


For spaghetti, linguine, angel hair andfettuccini

1 serving - 1/2 the handle - water level 1
2 servings- 1 full handle - water level 2
3 servings- 1 1/2 handles - water level 3
4 servings- 2 full handles - water level 4
6 servings- 3 full handles - water level 6
8 servings- 4 full handles - water level 8

Cook Time: servings/minutes

spaghetti - 1/13-14, 2/15-16, 3/16-18, 4/18-20, 6/20-22, 8/22
thin pasta-1/12-13, 2/13-14, 3/15-16, 4/17-18, 6/19-20, 8/21
angel hair- 1/11-12, 2/12-13, 3/13-14, 4/14-15, 6/15-16, 8/17)

Nov 30, 2010 | Microwave Ovens

1 Answer

My penn 950SSm reel doesn't lock out the handle spins backwards and lets out line after casting it and bail is flipped back how do i fix this


Try flipping it forward.. if that doesn't work... there must be a small spring inside broken. Just take it completely apart on a table. once apart look at the bail assembly, u should be able to find the broken piece. Take both broken pieces down to your local hardware store and ask someone for assistance. Someone should be able to help you find a piece very similar.

Oct 30, 2010 | Penn Spinfisher 950SSm Saltwater Spinning...

1 Answer

Penn gto 220 manual


hi, i dont have one but the penn web site should as when i pulled my alvey apart and to clean and didnt have a clue what was what.they have just about every model manual on the site and you can download and keep it for further use, check it out im sure a brand like penn would have a similar thing.

Feb 28, 2010 | Penn Gt Series Levelwind Reels 330GTi

1 Answer

I have a Penn 650 SS spinning reel Ihave loss the drag I have tighten it as hard as I can and it still has no drag


If the knob is not stripped, replace the drag washers under the drag knob.
Replace key #'s 6 and 56T with 3x 6-155 carbon drag washers, available here: http://www.mikesreelrepair.com/product_info.php?products_id=7806
this will bring your drag back to better than new condition!
Here's a schematic: http://www.mikesreelrepair.com/schematics/displayimage.php?pos=-4123

Best of luck!
Mike

Nov 12, 2009 | Penn Gt Series Levelwind Reels 330GTi

1 Answer

I started mower in tall grass. It started up and immediately stopped. Could not get it started. Replaced battery. Charged 12 hours. Still will not operate. Green light is on. Noticed the blade seems to...


After charging the mower, you must place the safety key in the mower before it will start. On models that have a bail handle, be sure to pull the bail handle back to the mower handle before engaging the start lever. If your mower still does not start, remove the safety key and ensure the bail and start lever are in the "off" position. Then firmly re-insert the safety key, pull the bail handle to the mower handle and engage the start lever.

Note - It is important that the bail and start lever are returned to the "off" position before inserting the safety key.
Give it try, if it still will not operate you may have to take it in for service.
Good luck, let me know.
Regards,

Jul 30, 2009 | Black & Decker 19" Electric Lawnhog...

1 Answer

CD Player tray will not rotate or open or close - no power


my cd player will open and rotates but will NOT play, can anyone help me?

Oct 09, 2007 | Audio Players & Recorders

Not finding what you are looking for?
Penn Gt Series Levelwind Reels 330GTi Logo

512 people viewed this question

Ask a Question

Usually answered in minutes!

Top Penn Sport & Outdoor - Others Experts

raysaw

Level 2 Expert

231 Answers

ray gallant

Level 3 Expert

43083 Answers

Tom Chichester

Level 3 Expert

34193 Answers

Are you a Penn Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...