Question about Simpson Garden

2 Answers

How do I remove wheel? from pressure washer? - Simpson Garden

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 250 Answers

You first have to pry the cap off the wheel with a screwdriver then under the cap there should be either a pin which you pry off or a nut which you loosen.

Posted on Mar 19, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Actually, after you remove the cap, you will find a retainer with multiple flanges that holds the entire wheel assembly on the axle. I used a screwdriver to make enough space to get a small wheel puller under it and it slid right off. Then I slid the wheel assembly off and replaced the wheel. The whole process took about ten minutes.

Posted on Aug 04, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing a starter rope


Remove the 3 or so screws that secure the pull rope housing to the top of the motor. Flip it upside down and it should be pretty obvious as to how to remove the spine loaded piece that the rope goes on. Thread the new rope thru the housing and wind it up on the spindle. Make sure before you put it on that the rope pulls out and retracts like it should.

Jul 30, 2016 | Homelite 6796881 308451006 Hilmore Husky...

2 Answers

How to get detergent to feed into Greenworks 1700 psi washer


The only way that it will feed detergent is by using the correct nozzle for the detergent. It's a lower pressure tip which allows the valve for the detergent to open. It's the black tip. It's either that or if it's an older one, there is a twisting wand that controls the pressure and spray pattern, which has to be twisted to the widest pattern with lowest pressure

Nov 10, 2014 | Greenworks 1700 PSI 1.4 GPM Electric...

2 Answers

How to repair non-functioning detergent bottle


Are you really sure it's not working? Most of these only dispense detergent when the lowest pressure spray head is attached. If that's not the problem then the next most likely thing to check for is a blockage in the tubing that connects your detergent bottle to the main unit. If this was not fully rinsed out after the last time it was used, any residual detergent remaining in the line will often solidify which results in blocking the line. Good luck

Nov 10, 2014 | Greenworks 1700 PSI 1.4 GPM Electric...

2 Answers

How do I remove the detergent tank, so I can empty and rinse it?


You have to remove the outer coverings to get down to the tank or if you can get to the bottom end of the pressure hose, you may be able to slip off he plastic supply hose to the tank and back lush up the hose and rinse the tank out. Never leave detergent in the tank, it will congeal over time and block the line.

May 12, 2014 | Greenworks 1700 PSI 1.4 GPM Electric...

1 Answer

Anybody know how to remove the wheels on a Husky 1750 power washer?


where does the link-mechanical gov. rod connect to the carburetor on the craftsman pressure washer number 919.762350.

Sep 28, 2013 | Dayton Wire Wheels Dayton Twin-Piston...

1 Answer

How do I remove the wheel from my gas powered pressure washer?


usually its an end cap that has to be pried off some are covered by a plastic cap if so you will have to get another because these have permanent fasten and will have to be broken off

Aug 07, 2013 | Psi Blue Max 2200 High Pressure Gas Power...

1 Answer

How to replace wheels on Excell VR2522 pressure washer


Anon, The wheel is probably held on by a push nut/cap. The easy way to remove is to cut through the cap retainer with a dremel tool part way and pry off with screw driver, these caps are not normally reusable after removal, check hardware store for replacement.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
DeVilbiss Excell VR2522 Type 0 Gas Pressure Washer Parts
Remove CM 1200 Lawn Mower Wheel Retainer Clip on Lawn Mower Wagon Carriage...
https://answers.yahoo.com/question/index?qid=20130208122204AAcj7mW

Jan 28, 2013 | Garden

1 Answer

Pressure washer tires


Your car should have a Jack located in the trunk (search for it, it may be hidden on the sides or with the spare). The Jack will have with it instructions on to specifically remove your vehicle's wheel. It will also have with it the necessary equipment (usually just something to remove the lug nuts). Jack up the car (place jack correctly), remove hub cap or wheel cover as necessary, then remove lug nuts to remove the tire. Pressure wash as desired, then place back on the car. Lower the car, but don't tighten the lug nuts fully until the car is back on the ground. Repeat for each tire.

Aug 02, 2012 | Honda Garden

1 Answer

Hi, could you please let me know how do i remove the wheel,,,ie i have a flat tire and i want to repair/ replace it...Thank you so much for your reply in advance. Keith.


Sir, there shoud be a just a nut to remove. Unless it has a soldered cap on the end? If so ... you have to be a little handy. You can use any type of small piping which will replace the old rod and just cut to size needed. You can drill a hole through and cotter pin to keep wheel on. (That's what I do... )

Mar 18, 2011 | Dewalt DPH3100 Gas Pressure Washer

Not finding what you are looking for?
Garden Logo

Related Topics:

2,412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Simpson Garden Experts

John Trevino

Level 3 Expert

1383 Answers

JOHN LAPIER

Level 3 Expert

2428 Answers

ray gallant

Level 3 Expert

43005 Answers

Are you a Simpson Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...