Question about Pride Mobility Products Health & Beauty

Open Question

I purchased a 3 position lift chair about 2 years ago,. this is it,s #LB22890920 the yellow sticker on chaie #6520 also on bottom #DWR1234L248. We have not been abusive with the chair however it is now falling apartn the arms are loose as is the back On the bottom front one side of the chair is lower than the other, my question, how long is the warrenty on chair and what do I do about it? I am a disabled 82 year old, my husband of 61 years recently passed I need the chair

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

6ya.com

Download 6ya

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Slinteriors
  • 8617 Answers

SOURCE: Samsung 61" DLP 3 Blinking lights.

all 3 lights blinking means lamp has a fault the service manual says replace the lamp. If you need the service training manual for that model let me know and I will post the link as the training manual has excellent trouble shooting breakdowns for that model DLP

Posted on Mar 26, 2008

  • 1 Answer

SOURCE: Maytag ice maker

I have maytag msd2756deq the water in icemaker is not comming. I replaced the dual water valve too.

Mani

Posted on Aug 03, 2008

  • 384 Answers

SOURCE: dead and wont move cant charge but batties are ok

sounds like a dead battery on the unit. see if you can get it replace .

Posted on May 24, 2009

mattofilms
  • 110 Answers

SOURCE: '07 5403 John Deere Tractor lift arm will not lower

some-times the 3pt linkage can go past the top position.

When this happens - you will need to force! the linkage arms down.

Posted on Jul 02, 2009

  • 175 Answers

SOURCE: My Pride (Ameriglide) Backpacker Plus Lift Stops

If it's stopping in the same spot, it is a limit switch that isn't making contact with the lift sensor.
Here's a link to the wiring diagram that shows where the limit switches are.
ftp://webfiles.pridemobility.com/pdf_files/ipbs/domestic_us/silverstar/us_backpacker_plus_ipb.pdf

If it is tripping the circuit breaker, either your are trying to lift too heavy a weight, or the motor is pulling too much amperage due to previous abuse, or misuse. These are good lifts, and if you bought it new, then get ahold of your dealer and Pride will fix the problem. If you bought it used, they may have been using it to haul concrete...who knows?

Posted on Jul 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can be doene with our executive office chair as it will not remain in the raised position. After raising it, then sitting, the chair slowly sinks down? What is the problem or what can be done.
The hydraulic gas lift is broken. If you want to fix it, you will need to find/buy a replacement. This is a common problem that happens with most all chairs, even if they are rated for heavier weight/long term use, they still do not seem to last more than 1-2 years of use at the most.

Sep 06, 2014 | Serta Big & Tall Executive Chair, Black...

1 Answer

We have a pride jazzy 1143 select power chair. we have had problems with the batteries going bad. I purchased a new set of batteries last December. in June they would not hold a charge and I purchased a...
charger is no good or is not the correct charger for that chair suggestion have a dealer tech replace a original charger in chair,it should have a 3 yr warranty anyways

Oct 22, 2013 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

Switch not working
I have an older electric Perfect Chair model and the switch has go out twice.
To fix mine here's what I did. you will need a butterknife, scotch tape, flat screwdriver, allen head wrench to fit screws on inside panel.
1. Scotch or painter tape on the wood around the switch so as not to scratch it.
2. Pop the switch box out of the wooden chair leg by using a butterknife edge (similiar flat tool will work).
3. There are six wires attached to the switch-single orange, double orange, single yellow, double yellow, blue one and a red one. Diagram which
wires go where so can hook back up correctly.
4. Unhook the wires from the switch.
5. Easier to rehook up the wires if remove the panel from the inside of the wooden chair leg. Need the correct size allen head or six sided wrench to remove the the 3 screws on this panel.
6. Open the switch by popping up the button. gently use a small screwdriver to do this.
7. There are 2 small metal slips/pedals at the bottom of the switch. the switch stops working when one or both of these get out of place.
8. Need to replace the metal pedal in correct position.
9.Replace the the button on the switch carefully to avoid disturbing the metal pedals.
10. Hook up the switch wires-see #3 and 5 above. my chair worked after this fix ! let me know if this helps - rhph@sbccglobal.net

Apr 05, 2013 | Human Touch The Electric Zero Gravity...

1 Answer

Blinking yellow wrench light on pride jazzy 614 HD
Your version has a Dynamic Controls model controller and joystick.
Unplug the charger and engage the motor/brake lever so the chair is no longer in free-wheel mode (con't push by hand)
Turn the chair off, wait 5 seconds, turn the chair back.
If chair still does not run and your wrench is flashing you have a problem. Count the wrench flashes - the flash count indicates the error detected. 3, 4, 5, and 6 flashes indicate and error with the motors.
3=Left motor fault
4=Right motor fault
5=Left brake fault (may not be engaged)
6=Right brake fault (may not be engaged)
Any other fault code usually means the electronics or wiring is bad and not worth fixing.

Jan 06, 2013 | Pride Jazzy 614 Hd JAZZY 614HD

2 Answers

We have a williamsburg chair inc. crib without instructions. The sticker says Williamsburg Chair Inc. Laona Wisconsin but I can't find them online How can i get them?
I have a crib from the same compayn purchased at JC Penney late 1983 early 1984. I am looking for the hardware. I could figure out how to put it together if I have it all in front of me. It has been 20 years though.

Apr 20, 2011 | Baby Gear

1 Answer

Can I or how can if possible return the Pride Lift Chair to normal seating position manually.Thank you.btrapp@sasktel.net
The easiest way to do this is to tip the chair forward so that the top of the chair and the arms are on the floor. The weight of the chair will be off the lift frame in this position. Look at the motor and you will see it connected to the frame with 2 hitch pins.
It is easiest to remove the top hitch pin which will now be on the bottom because the chair is upside down. Pull the clip (looks like half of a paper clip) from the pin that goes through the square chair frame and motor round tube. Pull out the pin by lifting the bottom of the motor slightly(now at the top because the chair is upside down)with your left hand and pulling the pin out with your right hand. Find the two nylon washers that have fallen out when you do this.
Swing the motor tube out of the way toward the front of the chair. Hold on to the pin, clip, and 2 nylon washers for re-assembly. Hope this helps.

Dec 26, 2010 | Pride Mobility Products Casual CL30KD Lift...

2 Answers

How to open printer to change cartridge?
In order to replace the cartriage, please follow the steps below:
1 Keep the printer on.
2 Lift the printer (scanner unit) until the scanner support keeps it open.
The ink cartridge carrier moves and stops at the loading position unless the printer is
busy.
3 Squeeze the tabs on the cartridge lids, and then lift the lids.
4 Remove the old cartridges.
5 If you are installing new cartridges, remove the stickers and tape from the bottom of
the cartridges.
6 Insert the new cartridges. Make sure the color ink cartridge is secure in the left carrier
and the black cartridge is secure in the right carrier, and then snap the lids closed.
7 Lift the printer (scanner unit) and push the scanner support back while lowering the
printer (scanner unit) until it is closed.

Sep 15, 2010 | Dell A920 InkJet Printer

1 Answer

I have an e-74 error, nothing works. The console was purchased at Costco 2 years ago?
As long as the warrenty sticker has not been tampred with microsoft will cover the repair of this free of charge in there 3 year warrenty period just contact m/soft customer services

Nov 25, 2009 | Microsoft Xbox 360 Console

2 Answers

How do I remove the chair from my Pride Mobility Jet 3 power wheel chair? The manual just have one line of description! Do I need to remove the chair before getting by hands on the battery? My Jet 3 is of...
There's a lever on the side of the chair that you disengage to unlock it. First, make sure the chair is in gear and power is off, then unplug the Joystick from the base; just follow the cable coming out of the joystick to the rear of the chair where it plugs in and rock it back and forth to unplug.
Unlock the seat with the lever, and turn the seat slightly to the left or right and lift up. Usually, it will come right off. If it's been a while since it's been removed, or if a heavier person has been bouncing atop it, it may need more coaxing. Try squirting some WD-40 at the base of the seat where the pole connects and let it run down into the shaft of the pole. Wiggle seat back and forth a bit and try lifting at the same time.

Now you can access the batteries by lifting up on the corners of the cover called the shroud. These are held on by Velcro strips so just pull up and they will give way. You will see the two batteries inside. Replace them with sealed, gel-acid deep-cycle batteried, about 32-34 amp-hour rating. Fully charge for two or three hours before using. On first uses, let the batteries discharge almost to the red zone before charging overnight. After a week, they will be well broken in. Good luck.

Jun 30, 2009 | Jet 3 Ultra Power Chair

1 Answer

Missing instructions on how to charge battery for MPV4
bad/old batteries

Jan 11, 2009 | Electric Jazzy 1115 Power Wheelchair

Not finding what you are looking for?

View Most Popular

Health & Beauty

Related Question

What can be doene with our executive office chair as it will not remain in the raised position. After raising it, then sitting, the chair slowly sinks down? What is the problem or what can be done.

  • Serta Big & Tall Executive Chair, Black 9783

Open Questions:

0 Answers

Jazzy 1120 goes in circles to the left. started only occasionally now always. sometimes turning pilot controller off/on corrects problem. motor brushes ok

Oct 07, 2016 | Pride Mobility Products Used Jazzy...

0 Answers

My Celebrity Pride X Sport was fine 30 mins later it showed a Speed POT fault. Charged batteries overnight pressed the reset and all fixed!!!!!

Aug 14, 2016 | Pride Mobility Products Pride Celebrity X ...

0 Answers

I get 1 flashing speed LED when I power on my Jazzy 600 xl

Jul 16, 2016 | Pride Mobility Products Pride Jazzy 600

0 Answers

Radio wont come on it said to punch in code did that and still didnt work what can i do?

Jun 25, 2016 | Pride Mobility Products Used Jazzy...

Health & Beauty Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Pride Mobility Products Casual...

Pride Mobility Products Jazzy...

Pride Mobility Products Jazzy...

Pride Mobility Products New...

Pride Mobility Products Casual...

Top Pride Mobility Products Health & Beauty Experts

wcdoc1953
wcdoc1953

Level 2 Expert

278 Answers

Colin Taylor

Level 2 Expert

346 Answers

Robin Hill
Robin Hill

Level 3 Expert

1263 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...