Question about Hobart A200 Stand Mixer

2 Answers

Type of lubricant for bowl lift

We purchased a used A200 at auction, works great, but my daughter who is using it said the bowl lift needs to be lubricated, I downloaded the manual for this mixer and it does say it needs to be lubed 1xmonth, but doesn't say what with. What kind of lubricant do we use? Colleen

Posted by on

2 Answers

Go to an auto parts place and buy some Lubriplate grease and use this on the assembly.

Posted on Aug 05, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Spray WD40 around the handle where it goes into the base houseing.

Posted on Nov 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I Need an owners manual for a Spar 200J mixer. Any info greatly appreciated


Contact Spar directly to request an owners manual.

Oct 23, 2014 | Food Mixers

1 Answer

Was just givin a hobart a200 was in a school warehouse for at least 1o years attach.shaft and seals replaced by hobart 6 month before put in storage runs great smooth no gear noise BUT fromm sitting bowel...


Ogrin56,

The problem is in your lift handle cams, you need to take the pedistal apart and clean and grease all the cams. I take them apart and wire brush them and use white lithium grease to keep them from freezing up.

Feb 26, 2011 | Hobart A200 Stand Mixer

1 Answer

Hi, I have a used Hobart A200T and the bowl yoke piece moves up and down slightly, even under a light load. It makes an annoying clanking noise. It's as if a spring somewhere is looser than it should be....


You may be correct about a loose spring. Check this:

Carefully lay the mixer on its back side to access the bottom of the mixer. Remove the cover screen covering the opening in the bottom of the mixer. Using an extension and appropriate socket, be sure the nut of the bowl lift rod is snug, slightly compressing the spring of the bowl lift rod.

Jan 26, 2011 | Hobart A200 Stand Mixer

2 Answers

The lever to adjust bowl height will not move.


most of the times it is because of build up between lift handle and pedestle case use wd-40 and even some heat from a torch to help loosen up stuck handle. also wd-40 the ways on the mixer ped. where the bowl yoke is

Dec 15, 2009 | Hobart A200 Stand Mixer

1 Answer

How to adjust bowl height on 20 qu hobart mixer.It is an old A200 1/3 hp Paddle is to high in bowl and will not mix dough on bottom and sides of bowl


you need to remove splash shield, tilt mixer back,with a long screwdriver adj. the set screwclockwise to decrease clearance for beater to bowl clearance,always use b beater when making adj. clearance should be .054" to .115".also make sure there are no deformities in btm of bowl which can cause you problems.dont forget to vote

Dec 12, 2009 | Hobart A200 Stand Mixer

2 Answers

Still need type of lubricant and diagram as to where to put it.


You will need a food quality grease. Contact a local restaurant supply store and ask them to assist you. Perhaps they will do so for the good will....a pix in the local paper....etc. good luck.

Mar 10, 2009 | Hobart A200 Stand Mixer

1 Answer

My A200 mixer is very old and the lubricants need to be changed.


http://www.hobartfood.com.au/products.asp?CID=60 go to this page and you will have all the info you need. good luck with it. please rate my answer as a fixya! Get back if i can be of additional assistance . take care.

Mar 10, 2009 | Hobart A200 Stand Mixer

1 Answer

A 200 mixer. the bowl lifting lever hits the bowl and guard.


If it hits the bowl its been dumped on the side and bent it. I have done this on sight I get a mapp torch and use a pipe wrench large one and heat it up at the bend where it goes in side and bend it out. or you can buy a new one take the head off four bolts under head and one roll pin inside easy to see and replace arm. The bending is quick and cheap. it will work like new be sure and clean and luber slides wd where it goes in neck.

Dec 23, 2008 | Hobart A200 Stand Mixer

3 Answers

Hobart A 200 Mixer - Lube


HI Joe
I have the wrong greace in my A200 standmixer i need to know what kind and how much to put in gear cace. thank you

Jul 17, 2008 | Hobart A200 Stand Mixer

1 Answer

Hobart A200


amy, depending on how old your mixer is there are 2 types of clutches for 1st gear.these could be your problems--a key is sheared on the shaft--shaft/gear is broken.the bottom part of the mixer where you put on the attachements is called the planetary,does it look like it has moved down?you could tell if the dough hook,wire whip,ect,ect is hitting the bottom of the bowl.if this is the case its just simply tightening the 2 nuts next to the beater shaft.if this is not the case you would have to dissasemble the transmission.let me know.

Jan 11, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Hobart A200 Stand Mixer Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1138 Answers

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Shira

Level 2 Expert

119 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...