Question about Pioneer Televison & Video

Open Question

Can no longer tune Pioneer PDP-427XDA to digital channels. When attempting to tune digital channels I receive the error: "This is an invalid operation because there is no Channel Table in DTV". This was working fine this morning.

Posted by on

5 Suggested Answers

  • 93 Answers

SOURCE: HL-R6167W tv reception problems

Are you using a Hd cable box/directv or dishnetwork box?Or you are using your coaxial cable straight into your TV coax input?
Solutiondoct

Posted on Nov 11, 2008

ladywinn
  • 5138 Answers

SOURCE: ABC DTV channels have distorted

Problem could be in the Main Board its the board that has your cable IF and AV jacks .
Encvompass Parts Distribution 1-800-638-3328

Posted on Sep 15, 2010

  • 2 Answers

SOURCE: Digital Tv is stuck on a channel

I have found the solution at last :)
Put the TV in standby and press these buttons in order
Info, Menu, Mute and Power on.
You will then see a hidden menu, on line 12 select reset
Bingo :)

Posted on Dec 30, 2007

SOURCE: Grundig colour tv lost digital channels

go to menu, digital setup, then auto tune all the channels again. it worked fine for me :D

Posted on Apr 04, 2008

ginko
  • 19396 Answers

SOURCE: how do i delete a dtv channel

Yes, usually on most models you can delete channel for presets. Depends on the digital box model, or if TV has built in digital, on the TV.
Post here digital box and TV model, I will see if I can find detailed instructions.

Posted on Sep 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pioneer plasma model PDP-507XA. how can I tune a TV channel?


The PDP-507XA only has an analog tuner. You will need a set-top box (digital to analog converter) to receive over-the-air signals in most places. For analog cable, you need to set the source to TV. Press the Select button, if needed (it's above and to the left of the arrow keys), to put the remote in TV mode. There is also an Input button on the TV. If the Channel Up/Down keys do not work, you need to reset the TV Press the Home Menu button. Navigate to the Setup menu (Up/Down arrows followed by Enter) and select Auto Installation. Enter your password for the TV; the default password is given in the manual on page 41. It's available from Pioneer here: docs.pioneer.eu/Manuals/PDP_507XA_ARE1430_manual . Set the Language (use the Up/Down arrows followed by Enter. Then use the Left/Right arrows to change the setting). Then set the Country. Press Start to begin a scan for channels. Alternatively, select Analogue TV Setup and enter the password. Then identify the correct receiving system. Manually enter the channels in the Search area. Set Store to Yes to save channels.

I hope this helps.

Cindy Wells

Feb 14, 2016 | Pioneer Televison & Video

1 Answer

I'm Italian and I live close to Gorizia, I can't see some DVB channel with my PDP-4270XD TV plasma. Other TV set haven't any problem. It's necessary to make a new Download? Please give me a...


You might try this.
Go to the Scan for More Channels option in TV Signal Setup.
First delete all the channels shown and then do a rescan.
This worked for me when my cable company switched to all digital.
For some reason WMC picked up the old channel map on the existing
channels and I could not tune them even though they showed in the guide.
Hope this helps! Take care and please Remember to rate/vote and give me
4 Thumbs Up for me to continue for Helping out the Community :)
Thanks

Jun 26, 2011 | Pioneer PDP-4270XD 42 in. HD-Ready Plasma...

1 Answer

I need the unlock code for a Pioneer PDP-R05G trap switch


Hello

Three digit codes for Pioneer are:-
004/ 009/ 090/ 179/ 185
Four digit codes for Pioneer are:-
0185 0181 0072 0004 0009 0090 0179

Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
OK.

Jan 14, 2011 | Televison & Video

1 Answer

What tv did an pioneer PDP-R05U go with?


Here's a list of Pioneer plasmas using the PDP-R05U media receiver:
PDP-4345HD, PDP-4350HD, PDP-4351HD, PDP-5045HD, PDP-5050HD, PDP-5051HD

Mar 10, 2010 | Pioneer PureVision PDP-5050HD 50 in....

1 Answer

Pioneer PDP-RX06XE has no picture


check PDP 436XPE UNIT may be Y board short...or need factory restore to the original state....

Nov 18, 2009 | Pioneer PDP-4350HD 43 in. Plasma...

1 Answer

After thunder all my digital channels have gone when i do a search it cannot find any channels says no signal


mostly if thunder hit the anttenna or satellite receiver, the tuner module will be affected , so try changing this module might solve your problems.

Jul 09, 2009 | Pioneer PDP-5020FD 50 in. Plasma HDTV

1 Answer

Suddenly cannot tune


Reset everthing in the menu. Mine does this every few months or so. I scroll thru the menu option until a come to a reset thing.

Dec 18, 2007 | Pioneer AirWave XM2Go Satellite Radio...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71126 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jaime Hernandez

Level 3 Expert

2275 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...