Question about IBM Bladecenter S Raid Sas Module - - 43W3584 Storage Controller

Open Question

Hello !!! I have problem with SAS RAID Controller Module(43W3584). On the BladeCentre S was installed SAS Connectivity Module (39Y9195). The storage HDD were connected to hosts and everything works fine. Then it was necessary to install SAS RAID Controller Module(43W3584). I disconnect all connected hosts, shutdown BaldeCentre, pull out the SAS Connectivity Module (39Y9195), install SAS RAID Controller Module(43W3584) with Battery Modules. After Switching on the BaldeCentre update all firmwares ( AMM, SAS RAID Controller Module, Storage Module, Disk). But the system have problem, there is amber information led . What could be the problem?????? Thanks.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: Raid 0 on Intellistation 6221?

That particular work station comes with both IDE and SCSI drive interface controllers. The IDE drive should be used for your OS. The SCSI drives for your data storage. Now, the issue is to get the SCSI to work in RAID_0 as I understand.

You iwll need a RAID controller such as Adaptec AHA-3940AU WD SCSI Host Controller, which may be found on eBay (used) for a very affordable price. The driver software may be downloaded directly from Adaptec, so I suggest you do that in the iterim peroid, and store drivers on a USB thumb drive.

Hope this helps you.

Posted on Dec 29, 2008

Ad
  • 105 Answers

SOURCE: new install scsi hard disk no detect in ibm x3400 server

you will need to add the new drive to your array bbfore it will how up to be formated do this throught the array configuration util



Regards Al "alstech"

Posted on May 26, 2009

micromatikal
  • 2777 Answers

SOURCE: IBM Total Storage DS400 I just did a ot sway

Hello there, I am a former IBMer that worked with storage arrays all the time, but I am confused on your issue here. I think you may have missed a few characters in your first couple sentences here:
IBM Total Storage DS400I just did a ot sway replacement of a failed controller.... IBM ServeRaid mgmt displays the same same failed controller status.


So have you replaced the failed controller? Sometimes you need to remove the definition from the system of the one controller and re-add it for it to recognize, but shouldn't need to.
Let me know some more info and I can definitely help you here.
Thanks Tim

Posted on Sep 10, 2010

  • 1 Answer

SOURCE: Boot problem with IBM xseries 206 - SCSI Drive and SATA drive

Not a solution: just a follow up. Did you work this out, as I have the same problem now. For others info: the xseries 206, has 2 sata connections which can be configured as a sata raid. It also has 3 hot pluggable scsi slots. When the sata drives are not connected it boots off the scsi to win server. As soon as the satas are plug in ( 1 or 2, raid or not) it wants to boot off the sata drive. Any help would be great.

Posted on Dec 15, 2010

smb_146
  • 252 Answers

SOURCE: i need a driver for my sound card

Hi!
You can download you drivers here:
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/netvista_drivers/dsiz31us.exe
Or
Go to supoort.lenovo.com using Internet Explorer and use Run AutoDetect.
Thanks

Posted on Oct 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A disk read error has occurred when booting a Dell PowerEdge 2950. Passes all diagnostics. Will run chkdsk from CD. Raid battery was degraded at last reboot but all disks showed to be fine. Raid 1


what OS?
what disk?
no raid card stated, no array stated, no type of array stated.
One can put 100s of RAID cards in this server.
both raid cards or HBA cards,(forJBOD)
i can fix any server, but first need to know what is in the box first
you meant the boot disk has errors, right,? boot.
that would tell me the disk IS BAD.
but if and ARRAY , that means you must run SMART tests
on the disks, 1 by 1 to find the bad disk.
if smart shows its bad, or weak its for sure BAD.
on real servers. the server sends you email, (set up right)
telling you disk 3 in a RAID 6 is bad, replace it now.

are you running hardware or software raid, or HBA or
fake raid cards, (4 classes there.!)

the base system new has.
4 port SAS 5/i integrated SAS controller (no RAID_
and optional, from DELL , news.
Optional PERC 5/i integrated SAS/SATA daughtercard controller with 256MB cache,
PERC 4e/DC, PERC 5/e adapter

or any of 1000s of other aftermarket cards there.
I run LSI 9361s (with MSM appl loaded)
this card will tell you what disk failed every time no kidding.
so will the PERCs setup correctly
the PERCs and my LSI and my HP raids
all have installed monitors for the RAID ,a program that runs full time all the time, and reports errors , many ways,
did you load that first and use it? seems not.
as no mention of SMART at all.
good luck.
Im not sure the names on DELL , MSM like software.
ah its OSA
never run a PERC lacking this APP. or you can not keep the server on line,.

http://www.dell.com/support/search/us/en/04#q=Dell%20OpenManage%20Server%20Administrator&sort=relevancy&f:langFacet=[en]

Mar 05, 2018 | Dell Computers & Internet

2 Answers

How do I make RAID 1 HDD's appear on Bootable USB WinXP Install?


a waste of time and effort installing win xp on anything as it is no longer supported by Microsoft and had real problems with drivers for just about everything
install win 10 and it will work

Feb 28, 2018 | Dell POWEREDGE 1950 Server

1 Answer

Can not setup RAID 1 on an IBM X3200 M3 Server


you can access the raid controller using the BIOS and system devices>>> refresh>>> then select the controller then create your raid...

don't know why they move out from the POST the controller its really stupid''' Sorry..

Feb 04, 2012 | IBM System x3200 M3 7328 Server tower ...

2 Answers

Windows 2008 r2. cannot find SAS HDD during install. I have tried to use drivers from Delll official site. But it doesn't help.


What RAID controller are you using? Also, you must first configure RAID in CTRL-C (SAS 5/6) or CTRL-R (PERC 5/6) before even loading the driver will help.

Mar 18, 2010 | Dell PowerEdge 2950 (becwfk1_6) Server

2 Answers

I have a Smart Array 431 RAID controller out of an old Compaq server. I cannot find any documentation on the card that describes the pin headers and their functions. There are 5 headers on the board: E1,...


Find below the controller components for Identification purpose.
1.Port E1
2.PORT E2

The Port E1 and E2 connectors is made up of single mini SAS HD connector which can take two mini SAS Hard disk or single SAS Hard disk while the cache module connects to a capacitor pack and cache module connects to a battery
-SAS HD receptacle connector, which can
accept either two Mini
-SAS HD 4x plug connectors or a single Mini
-SAS HD 8
x plug connector.
**The 2 GiB cache module connects to a capacitor pack. The 4 GiB cache module connects to a battery pack

3.CACHE MODULE
4.Battery /capacitor pack cable connector

smart array 431 raid controller card-0merpufmz0rxpqnykc4eyfz5-3-0.png

Jan 04, 2018 | Compaq Computers & Internet

1 Answer

Constant beep on poweredge 840 appears to work alright


Hi

Besides standard beeps codes indicating Processor, CPU, Memory or Systemboard failures,
Dell PERC (PowerEdge Expandable Raid Controller) or SAS Controllers (Serial Attached SCSI) generate beeps to alert failures on the RAID sub-system.

From your description of the issues (when the beeps start), i suggest you check PERC or SAS setup. If you have Dell OpenManage Server Administrator installed, you can log-in and check for more information. Additionally, on the next reboot check the PERC/SAS/CERC boot up for any messages. You may also access the PERC (Ctrl+M), SAS (Ctrl+R) CERC (Ctrl+A) Management Menu for specific failures and attempt a rebuild (assuming you have a redundant RAID Volume).

You can also speak with Dell Support and raise a warranty call if the system has warranty.

Note: PowerEdge 840 would ship with PERC or SAS Controller. PowerEdge 700 will ship with PERC or CERC.

Mike

Apr 02, 2008 | Dell PowerEdge 700 Server

Not finding what you are looking for?
IBM Bladecenter S Raid Sas Module -  - 43W3584  Storage Controller Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top IBM Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Alun Cox

Level 3 Expert

2678 Answers

Are you an IBM Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...