Need instructions how to program this digital timer.Thanks!

1) Eurosonic appears to analog timer:
http://waterheatertimer.org/How-to-set-timers.html

2) There is new series of digital timers from china, also sold as Eurosonic:
Copy following link for possible manual. Always reset digital timers before programming.
http://waterheatertimer.org/Woods-timers-and-manuals.html#13568

3) Add a comment March 2013 and describe timer in detail

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Oct 2011. Utilitec has 2 in-wall timers that replace single-pole switch.
Open following links to identify timer and read instructions:
http://waterheatertimer.org/Program-wire-Utilitec-0192773.html
http://waterheatertimer.org/Program-wire-Utilitec-LW60418.html

Question posted under Intermatic ST01C, but Timer is not 100% identified since ST01C is battery powered, and should not lose programming or stop working with ordinary power outage.
Most digital timers have a battery or capacitor back-up for power outage.
Add a comment with description of timer buttons, or open link below to see most brands of in-wall timer.

Open following link for to identify Intermatic ST01C and Ei600 and download instructions:
http://waterheatertimer.org/ST01C-program.html#battery
ST01C timer has a battery backup. Power outage will NOT cause battery-powered display to fail, but power outage and power surge can cause any electronic timer to fail.
So either the battery went dead, or power surge ruined timer, or you don't have ST01C timer.

If ST01c display is not showing, then replace battery and then reprogram current time -or- manually re-set timer and then reprogram timer.

Hi

Programming:
Set present time
Then set ON time for program 1
Set OFF time for program 1
Then set ON time for program 2
Set OFF time for program 2
Most timers will not function if there is a conflict in programming > for example Program 1 says ON at 6 and OFF at 7 and Program 2 says opposite or has overlapping times
When events are set, press SET once > this will put timer in RUN mode

If manual override works, and you set programming correctly, but timer does not carry out instructions, I guess the timer is no good.

Intermatic has 24 hour timers with 2 on-off per day
http://www.intermatic.com/products/timers/consumer%20indoor%20timers/lamp%20%20appliance%20timers.aspx
Intermatic has 7-day digital timers (all digital timers today are 7 day where you select the day that each program works)
http://www.intermatic.com/products/timers/consumer%20indoor%20timers/digital%20timers.aspx


Thanks.

Check following link to identify timer and download manual:
http://waterheatertimer.org/Woods-timers-and-manuals.html

Woods timers go by more than 1 number and are repackaged and sold under different brands >> a few older Woods timers and promotional timers don't have manual on line.

Woods 49565 is also N1507 timer
http://waterheatertimer.org/pdf/Woods-49565-manual.pdf

If this is nor your timer, see all woods timers and manuals:
http://waterheatertimer.org/Woods-timers-and-manuals.html

I saw similar Westec timer at Target yesterday. Sears is supposed to sell Westec too. Buy timer and copy instructions.

Westec shows some manuals, but doesn't show TE55 product or manual for TE55
Other site reported problems with the TE55
http://www.amertac.com/content/home.nsf/Subjects/LIghting+Controls+Frameset/

I found manual for TE05, which might be similar
http://waterheatertimer.org/pdf/TE05WHBL-WTBL-INSTRUCTION.pdf

CLICK HERE for the manual.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Here is the instruction manual your looking for:

Intermatic HB77R

Hope this helps and please remember to rate this!