Question about Sport & Outdoor - Others

Open Question

I need a user manual for my Leisure Works Model 919 Treadmill, which I have just bought used. It has started to beep constantly and the programs do not appear operational; we assume it needs to be reset.

Posted by on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: oil can caption on my reebok fusion treadmill (rev10301)

It means that you need to spray silicone between the belt and the platform it runs on

Posted on Jan 12, 2009

  • 2777 Answers

SOURCE: when i switch my power

What message does it give you, I think you forgot to include that in the question. Also what model number of treadmill is it?


Posted on Sep 13, 2010

  • 95 Answers

SOURCE: I have a TX350 sportcraft

I am not a fitness expert but I did want to pass along a few resources in case they may be useful. Here is a parts list for the TX350, and here you can search for treadmill repair companies in case you need to have someone in your area take a look at it. Hopefully you can find a solution without needing to spend money on repairs, though.

Posted on Mar 14, 2011

  • 17970 Answers

SOURCE: Need to reset fitstride T

Error : 4 Power circuit trip.

When happens:
Power circuit broken or motor locked or broken.
Do not use treadmill, call service. Fatal error.
It typically happens during workout (8Km/H to 14Km/H).

During workout (Speed 8Km/H to 14Km/H)? or when they start the treadmill (Start)?

Possible Solutions:
Turn off and on the power.
Push Stop + Slow together , and you are in setup mode.
Push Stop + Fast together in setup mode, and you are in Diagnostic mode.
Using fast, slow key to select "LAST ERROR : "(clear last error) and push Start to clear the
error. Push Stop key , and you are in Stop mode.
Now you are ready to test the treadmill.
Start the treadmill and check the Error message again.
Error 1, Error 2, Error 4, Error 40, Error 41 ?
Check the motor runs or not , when you test it ?

Warning : Do not step on the treadmill, it is very dangerous.

Hope help with this.

Posted on Apr 18, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wont turn on

Was it damp down there?

Mar 26, 2015 | Office Equipment & Supplies

1 Answer

Power go to treadmill but won't turn on

Try for a repair manual:
Are there batteries somewhere, that are dead and corroded? Another type of an exercise device I had was like that. Otherwise, the power supply to the boards and or the drive system may have expired.

Mar 26, 2015 | Office Equipment & Supplies

1 Answer

Lifetrack OMA-117 treadmill constant beeping not moving

1) adjust the REED swithc , see the diagram clean , and tight the wires connector very well.

2)Try to RUN the software calibration for diagnose, and troubleshooting.

God bless you

Jun 29, 2012 | Exercise & Fitness

1 Answer

Smooth fitness treadmill beeps every two minutes

Walk on a treadmill to calculate distance.
Most electronic treadmills allow you to program for an alarm or beep when you've walked a certain distance.
Try to turn off reading your owner manual.
And check if there are some error code?.

If you do not have owner manual go to this web:
and download free.

Nov 22, 2011 | Exercise & Fitness

3 Answers

I have a Proform 545s treadmill with incline and with ifit. When i start the treadmill it will no longer attain the programed speed. The higher the speed programed the fast the treadmill will go; however,...

It sounds a lot like it might be your Motor Control Board. You can find one used on varios websites (ebay if you're lucky). I found one for $149.00 on the following website:

I hope you got a good deal on it because it seems to be quite an expensive part.

Thanks and good luck!

Mar 21, 2011 | Proform Exercise & Fitness

1 Answer

Pro-Form Crosswalk Plus Treadbill back leg extension has free pdf downloadable manuals for proform.

Nov 12, 2009 | Proform Crosswalk 500 Treadmill

1 Answer

I bought a used treadmill and need a manual for it.

I need to know what brand the treadmill is and the model number I will be able to get u the manual

May 03, 2009 | Proform 575 Crosstrainer Treadmill

1 Answer

Stops running

LED Blink Patterns on the Control Board Treadmill Treadmill Maintenance How To Lubricate Treadmill Belt
Try to do this steps in order to fix it.
However if the problem persist.
Time to replace the Controller board Motor.
This board has 3 power supply control:1) Console Board 2) Elevation Motor 3) Main Motor.
One of IGTBs is faulty.

Oct 01, 2017 | Proform iLog 750 Treadmill

Not finding what you are looking for?
Sport & Outdoor - Others Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sport & Outdoor - Others Experts


Level 3 Expert

76846 Answers


Level 3 Expert

102366 Answers

Brad Brown

Level 3 Expert

16174 Answers

Are you a Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides