Question about Kenmore Oasis HE 27082 Top Load Washer

2 Answers

Kenmore Oasis washer will not turn on

The washer is about 15 months old and we have already had the circuit board changed a few months ago and now it will not power on. We checked the outlet and it has plenty of juice. We have tried the breaker, leaving the washer unplugged and not sure what else to do before the repair man gets here next week. Any suggestions?

Posted by on

  • 4 more comments 
  • 98 magred Aug 04, 2008

    my kenmore elite oasis 110.27086602 has the same problem. wife went to turn it on today and nothing...no power...checked the outlet and it reads 119V...any ideas?

  • Anonymous Aug 21, 2008

    went to turn it on and nothing totally dead

  • opie2 Oct 07, 2008

    kenmore oasis washer will not turn on

  • nelly80 Oct 14, 2008

    I have the same problem. it was working fine, for about 2yrs, and now sometimes it will not power on, and constantly beeps all day. We unplugged it for the night and the next morning and it started working again, but will not stop beeping.

  • Anonymous Apr 17, 2009

    washer is full of clothes and water and the dial is all lit up and nothing happens. if i push any of the buttons i hear beeps but nothing happens.

  • ccsicsek Apr 25, 2009

    I replaced the circuit board once, now I have the same problem, no power. It just quit working......

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I purchased a kenmore elite washer and dryer. my wahser quit working with no notice. it won't turn on. you guessed it warranty ran out.



thanks.
chad

Posted on Sep 29, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem. I used the unit 2 days ago and no problems- just bragged about the unit yesterday and now today it will not turn on and it is no longer under warranty. I also checked to see if power to plug and it is fine. Any suggestions?

Posted on Aug 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Codef1


This is a known problem with this model. Call 800-847-9083 and give them the model and serial number to see if your unit is covered by a recall on the control board. I called a few weeks ago and they sent the part and a tech to install it for free on my 3 year old machine.

Apr 29, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

2 Answers

F1 & F51 error on my Kenmore Elite Oasis HE washer


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Good news for Oasis F-51 sufferers! Sears will replace the electronic control board (the F51 prob) for free, in warranty or not. Serial #s for the bad board are: CS48 - CS52 or CT01-CT49. Call Sears at 800-847-9083.
You hv to rate me ‘very helpful’, or the call won’t get thru!!

Feb 08, 2010 | Kenmore Oasis HE 27082 Top Load Washer

2 Answers

In mid wash the Kenmore Elite Oasis HE flashes F51 and


check if basket turns freely. if it does replace the main board

Jan 28, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

2 Answers

Error F51 for Kenmore Elite Oasis Toploading washer??


bad main board or motor possitioner sensor.. most likely motor sensor.
China made junk parts with a million problems

Nov 21, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

My Kenmore Oasis washer just stoped working.


usually their is a # after the f . when you unplugged did you wait about 5 minutes if not try it, if you did, try again if its an f1 . unplug machine remove 3-4 screws on top of control panel and it will lift up and out, find the grey board their should be a black hose hooked up to the board. pull hose off and blow thru hose and blow thru piece on board that hose goes into . reassemble . plug back in and try it. if works great, if not may need board replaced. hope this works for you

Sep 18, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

3 quick beeps during cycle if you can get it to stay in a cycle


MY KENMORE OASIS HE IS DRIVING ME CRAZY! THE CYCLE SIGNAL CONTINUES TO BEEP AT LEAST 25 TIMES, STOPS FOR MAYBE 20 SECONDS, THEN BEEPS AGAIN ABOUT 25 TIMES. THE WASHER WORKS GREAT, BUT IT WILL NOT STOP BEEPING! HELP!!!!!

Sep 13, 2008 | Kenmore Oasis HE 27062 Top Load Washer

2 Answers

Kenmore oasis washer


This is a common problem with the Oasis. The problem is the User Interface Control board behind the control panel. There's a relay on the board that shorts out and causes the washer to randomly (and constantly) beep. This can also occur with the washer turned off. Since the circuit board is not serviceable it is recommended that you replace the control board. Searspartsdirect.com carries replacement parts for your washer. Just type in the model number and search under the console heading for the user interface board. If you are usure which part, I'm talking about, please post back with your model number and I can assist you. I hope this helps.

Aug 08, 2008 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Kenmore oasis 15 months old


hi over here in the uk we have home insurance if you have the same thing maybe it's worth looking to see if you can claim on that rather than spending more money on a new machine.

Mar 06, 2008 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Lid locked


Sounds like a falled board in the machine itself. At 8 months old, is your warranty still in effect? If so, may want to call the Searsman. Good Luck!!! Jim

Sep 03, 2007 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Kenmore oasis washer


Jenine, I have run into this problem on a few of the Oasis washers. In talking to the Whirlpool tech rep (Whirlpool makes the Oasis), I was under the understanding that they had some issues with the initial main board supplied in these washers causing the F code. Therefore, in changing this washer out, you probably received one in stock with the same board. What I would do, since it's under warranty is to have the technician order a board from the factory. Any revisions to the new board should be in there. As long as you have both water valves on, no clogged screens on the hoses and 120 volts at the outlet your washer should operate normally. Catriver...post back.

Oct 08, 2006 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
Kenmore Oasis HE 27082 Top Load Washer Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Ron Lankford

Level 3 Expert

5386 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

2mikecurtis

Level 2 Expert

65 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...