Question about Bosch Dishwashers

1 Answer

My Bosch dishwasher is driving me crazy! When it finishes a wash cycle it beeps twice every 10 minutes until the door is opened. We can't run the dishwasher at night after dinner unless we're SURE we aren't going to bed before it's finished. We've tried every combination of button pushing and can't figure out how to disable the beeps. We'd be happy to permanently disable it if we have to. Help!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,140 Answers

Hello there,

It would help to know the model number of the dishwasher, but on many Bosch dishwashers, you can switch the cycle cycle completion signal off as follows:

1. While holding the right-hand CANCEL/DRAIN button, also press and hold the ON/OFF button
2. When the LED above the CANCEL/DRAIN button illuminates and the beeping starts, release both buttons
3. Press the right CANCEL/DRAIN button repeatedly until the beeping tone is at the desired volume, i.e. silent!
4. Press the "ON/OFF" button again to set the volume.

On models with the wash cycle buttons on the top edge of the door, the CANCEL/DRAIN buttons aren't always explicitly labelled CANCEL/DRAIN. These buttons are also labelled RESET on some models.

On models with 3 and 4 wash cycle buttons, the right CANCEL/DRAIN button is the third button when reading from left to right. On models with 5 wash cycle buttons, the right CANCEL/DRAIN button is the fourth button when reading from left to right.

Please try the above then let me know if you need further assistance. Please state the model number or series (i.e. Integra) of your washer if/when replying.

Hope this helps.

Regards,
BElectric

Posted on Mar 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I reset our dishwasher


Open the dishwasher door sufficiently to see the control buttons, then hold the two buttons with labels "Cancel Drain" and press for 3 seconds.
Close the door. Wait nearly 1 minute for the dishwasher to complete the cycle.
Open the door and hold the "ON/OFF" toggle.

Reset Bosch Ascenta Dishwashers
Shut off the child lock if needed by pressing and holding "Open the door far enough to see the keys, then hold the "START RESET" toggle until the "ACTIVE" LED become extinguished. On the SHE5AM model of Bosch Dishwashers, hold the "START RESET" key until the display clock shows "0:01".
Close the door and rest about 60 seconds. On the SHE5AM, wait until the display clock displays "0:00".
Open the door and hold the "ON/OFF" toggle.

Apr 06, 2016 | Bosch SHE4AP06UC Dishwasher

1 Answer

I have a SHU5305us/u12 and my front door lettering got erase. anyone have a picture or a manual that tells me what each button means.


Cycle Interruption

As a safety feature the dishwasher will automatically turn itself off whenever the door is opened. However, if the door is opened quickly while in a wash or rinse cycle some water may splash out of the dishwasher. For this reason it is recommended that the machine always be switched off before opening the door.



To Interrupt a Cycle

1. Press the on/off button to stop operation.

2. Wait at least 10 seconds (or until the water noises stop) before opening the door.



To Resume a Cycle

1. SHU/SHI models, close the door and press the on/off button.

2. SHV models, push the on/off button and close the door.



Changing a Cycle

For Bosch dishwasher models SHI 6800 and 4320, SHU 5300, 5310 and 6800 press the program button of the desired cycle TWICE. For all other Bosch dishwasher models, press the program button of the desired cycle ONCE. The chosen cycle button (or the light above it) becomes illuminated, showing that it has been selected.

* SHU 3030 and SHU 3130 models do not have program lights.



Cancelling a Cycle

Each control panel shows which buttons to simultaneously push to cancel a cycle. Refer to your dishwasher to find the cancel drain buttons on your particular model.



1. Press the indicated buttons at the same time and hold for approximately 3 seconds.

2. When the drain pump noises stop and the LED display or clean light indicate that the end of the cycle has been reached, the dish

washer is reset.

3. Press the on/off button to turn the dishwasher off.

4. The dishwasher is now ready to run a selected cycle. Add more detergent if necessary.



Dado


25893572-cjqtzppbjhbnv3ly1nzv40fs-1-0_0.jpg

Oct 05, 2015 | Bosch Dishwashers

1 Answer

Bosch Dishwasher wont run full cycle. Stops/Beeps and says CLEAN.


Hello there,

Could you please supply the full model # off your appliance?

Mar 12, 2014 | Bosch SHX4AP05UC Dishwasher

1 Answer

Beeping won't stop at end of cycle


Our Bosch does the same thing, we just open the door shut of the power and close the door again so the heat can sanitize the dishes. I don't recall if there is an alert off button though.

Jan 08, 2014 | Bosch SHU9926UC Built-in Dishwasher

1 Answer

Bosch dishwasher beeping during cycle


Take the front kick panel off and see if anything under the machine is wet.

Jan 06, 2014 | Bosch Evolution 800 SHE58C02UC 24 in....

1 Answer

Beeping sound when cycle is finished just started after 8 years. how do I turn it off?


Hello,

Welcome to FixYa.

I think can answer your question..."beeping sound when cycle is finished just started after 8 years. how do I turn it off?"


Follow these steps...

**How to Operate the Cycle Completion Signal**


1. Open door, hold down program button (see
Beeper Table below) and simultaneously turn the unit "ON".


MODEL Program BUTTON

SHU 9950 Delay Start Hours
**SHU 9910-9920 Delicate/Econo** should be yours
SHU 8800/8810 Quick Wash

SHV 6800 Delay Start Hours
SHV 4800 Delicate/Econo
SHV 4300 Delicate/Econo


2. Release program button.
a. For SHV 6803 and SHU9950 models:
The display will blink with a code of "0", "1" or
"2". You are in program mode.

? If the display blinks with a "0", you will hear
no signal (indicates OFF).

? If the display blinks with a "1", you will hear a
LOW volume signal.

? If the display blinks with a "2", you will hear a
HIGHER volume signal.

b. For all other models with the beeper
function:

? If the machine beeps, then the Cycle
Completion Signal has been enabled.

? When you push the button again and it does
not beep, it means that the Cycle Completion
Signal has been disabled.

3. To change the program, press the program
button until the desired setting is selected.

4. Turn the Dishwasher off to take it out of
program mode.

* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.

Hope this answers your question and provides you with what you needed.

Thank you for choosing FixYa and good luck.

Please take a moment to rate the solution provided and a short testimony if you feel it's warranted, but also let me know if you require further assistance.

Regards,

Macmarkus :)

Nov 06, 2010 | Bosch SHU9915UC Dishwasher

2 Answers

Dishes not washed detergent still in compartment pump will not stop pumping bosch dishwasher


cycle stuck possibly..........unplug it or turn it off at the main electric box circuit breaker......wait 10 minutes and try it again.........

Feb 13, 2010 | Bosch Dishwashers

1 Answer

Dishwasher bosch beeping noise


Found this on the Bosch website..... see 2nd to last step
The Cycle Completion Signal
This Cycle Completion Signal is a tone that sounds to alert you when your dishwasher
finishes washing and drying your dishes. You can either disable the tone or set the volume.
To activate:
· P ress and hold the right “Cancel Drain” button then press and hold the On/Off button.
· When the light on the “Cancel Drain” button you are pressing illuminates and the tone
begins to sound, release both buttons.
· P ress the right-most “Cancel Drain” button until the tone is either at the desired volume
or is silent.
· P ress the On/Off Button. The Cycle Completion Signal is now set.

Sep 27, 2008 | Bosch Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18390 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...