Question about Konica Minolta DiALTA CF910 Copier

Open Question

How do I get the minolta Di450 out of SADF mode?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: SADF Mode problem

Try turning off the machine, pushing and holding the utility key and turning it on, don't take your finger off the key. You should see a blank screen with one touch button on it saying Trouble Reset. Press it, if the machine doesn't reset itself turn it off and one again.

Posted on Aug 26, 2007

Ad
jqsababa967
  • 145 Answers

SOURCE: Minolta Di450 has full toner but copy paper comes

try copying from the document feeder and of the glass,and make sure the exposure light comes on
if all ok check you transfer unit its. sits below the drum,when you open the fron door release the convayance lever and you can slide that transer corona out there are 2 thin wire make sure they are not broken ,

Posted on Jun 05, 2009

  • 1 Answer

SOURCE: minolta dialta Di450 Error message C-143E

The Document Feeder has only 1 Malfunction code for any problem with it.
If opening and closing the front cover (while it is turned on) resets it and you can use the machine, dont worry about it.
The unit was prone to this false malfunction code.
If it returns very often, then get an engineer to have a look at it.

Posted on Jun 12, 2009

wheatlandsvc
  • 1110 Answers

SOURCE: What about the code of 0500 in minolta

C0500 is a fuser heat failure code. This means the fusing unit (The assembly that gets hot and is located right where the paper exits the machine) is not heating up properly. This is most commonly caused by a thermal fuse failure.
Open the front door. To the left side there is a small cover held on with 1 screw. Remove the cover and with the machine turned on push the "trouble reset" button. This should clear the code so you can see if it comes back. Do this only once per 10 minutes!!!!
If the code comes back you will need a service technician to correct the problem.

Posted on Jan 03, 2010

Testimonial: "According to me you have good knowledge, Thank you for solving my problem..."

  • 53 Answers

SOURCE: error message C-13FA

The connectors on the PWB-B and Print head unit are not fully seated or excessive torque was used to tighten the two thumbscrews securing the Print Head to the machine. Also verify that the current firmware has been installed

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Erace the c-of24 on di450


The code refers to a sensor that looks at the drum - it might be dirty or something else is going on check this Fixya-link: Minolta DI450 error code C0F24

Jan 17, 2015 | Konica Minolta Minolta Di450 Di470 Di550...

1 Answer

How to reset to factory default


Sir, reset what part like access code etc. Di450 series great machines rugged. Service mode Memory Clear?

Dec 19, 2014 | Konica Minolta Minolta Di450 Di470 Di550...

1 Answer

Cant turn off c-24 on di450


Unplug it from power & computer for at least one minute the replug in. If that doesn't work contact the nearest Minolta repair facility or go to the Minolta web page for support.

Dec 13, 2014 | Konica Minolta Minolta Di450 Di470 Di550...

1 Answer

Username for scanner mode


look like the previous owner had a password for scanning , ask him

Jan 27, 2014 | Konica Minolta Minolta Di450 Di470 Di550...

1 Answer

Repair carriage wire of di450 photo copier


What carriage wire?
Is 2 wire in the transfer/separator corona.Is cut change.

Jan 06, 2013 | Konica Minolta Minolta Di450 Di470 Di550...

3 Answers

Minolta Di450 service code reset service code C1326


di450 . what is the solution of this code 1326?

Jun 09, 2011 | Minolta DI-2010F Copier

3 Answers

SADF Mode problem


Try turning off the machine, pushing and holding the utility key and turning it on, don't take your finger off the key. You should see a blank screen with one touch button on it saying Trouble Reset. Press it, if the machine doesn't reset itself turn it off and one again.

Jun 14, 2007 | Konica Minolta DiALTA CF910 Copier

Not finding what you are looking for?
Konica Minolta DiALTA CF910 Copier Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6161 Answers

Ben
Ben

Level 2 Expert

108 Answers

David Burkhart
David Burkhart

Level 2 Expert

210 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...