Question about Stanley Hand Tools

1 Answer

Hi I am looking for a 3/8 replacement ratchet for stanley 89-818B? colud you please help?! thank you.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 157 Answers

Hello. Here's a link to the main Stanley customer service, Try the toll free and I'm certain they will be happy to assist you. At the top, there is also a dealer locator to help you find the closest to you. Hope this helps.

Posted on Mar 29, 2011

  • Richard Crate Mar 29, 2011

    Sorry about that the link didn't attach. Here it is:

    Again, my appologies.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to use Stanley air ratchet

Put a couple drops of oil in the air inlet, then plug it into your air compressor. Make sure that your air pressure is at the recommended level. Attach socket and you should be good to go.

May 19, 2014 | Air Tools & Compressors

2 Answers

Hello my name is Lisa, I've just recently bought a stanley rotator ratchet and three stanley spark-plug socket kit, and I'm using the 13/16 to try to remove an old spark-plug, but I can't...

turn the thumb knob on top of ratchet to opposite direction and then try it in your hand first, now I have seen cases where if you are in tight quarters that the ratchet will change directions by itself because the knob rubs on something and causes it to reverse. good luck

Jul 30, 2011 | Garden

1 Answer

The spring in Stanley TR45 light duty sharpshooter does not work, where can I get a new spring?


From what I have read, and I've searched, Stanley doesn't make parts for this staple gun. Only found hammer tacker springs.
Here is the phone number for Stanley customer service: 800-262-2161
It's a remote chance that one of those might fit.....

Hope this helps. If it does, please place a vote for me. Thanks,

Handie Andie

Apr 06, 2011 | Stanley Tr45 Sharpshooter Light Duty...

1 Answer

I have a CP 828 3/8" air ratchet it turns but has no power and I have 100 PSI behind it. I have always oiled it. Can you please help me. Thanks, Rob

If you oil it regularly you may need to replace the veins inside the motor.When you do this be sure to check the bearings on each end of the motor.Also check the exhaust and inlet screens to make sure they are not clogged.

Oct 19, 2010 | Chicago Pneumatic 3/8" Heavy Duty Air...

2 Answers

I'm stumped -- I just bought a Stanley Heavy Duty TRA700. I took the "safety" off (the wire loop that holds the handle down), pinched the lever on the back and slid out the tray the staples go into. I...

The question here is what are standard staples in YOUR opinion? Are they designed to be used with this staple gun. What length are the legs of the staple 1/4" or less.

You cannot just use any staple in these guns They have to be the correct type either stanley or Bosh
Please rate my help++++Thanks for using FIXYA

Jun 20, 2010 | Stanley Chrome Hd Staple Gun Tr110

1 Answer

I need diagram and directions to change the ratchet on the drivers seat in a 1996 ford bronco. the bottom frame is broken and need to take it apart to weld the frame as you can not find a decent seat to...

Follow these steps to easily remove the driver's seat from ford bronco 1) Lean under the seat and unclip the harness that connects the seat belt sensor to the seat. You may need to use a small flathead screwdriver to pull the release open. 2)Attach the Mac Tools SC620B socket to the 3/8-inch ratchet and unbolt the seat from the floor. 3)Attach the 3/8-inch ratchet to the extension and then the socket. Unbolt the two bolts towards the center of the vehicle. These may be difficult to remove from the channel, but they will eventually come out. Then lift the seat out of the vehicle. 4) Now if you want to replace only ratchet then remove the ratchet from the seat and place new ratchet and reverse the procedure.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Mar 24, 2010 | 1996 Ford Bronco

1 Answer

Can you help with loading staples into a stanley sharpsshooter T50 staple gun

Look at rear handle bottom, Push in then pull out,load. Please rate. Thanks

Jan 25, 2009 | Stanley TR250 H Heavy Duty Heavy Duty...

1 Answer

Locked screen

Hi there,
I found a page with a video, on how to open a padlock - I hope this is what you need, it looks easy.
3325d60.png plz let me know how you go - maybe I know of a safe we colud open...


Jan 16, 2009 | IBM ThinkPad T20 2647 Notebook

Not finding what you are looking for?
Hand Tools Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Hand Tools Experts

Jim Thurston

Level 3 Expert

670 Answers


Level 1 Expert

35 Answers

Don Numinen
Don Numinen

Level 2 Expert

62 Answers

Are you a Stanley Hand Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides