Question about Neff U1661 Double circotherm super Electric Oven

1 Answer

No heat Recently the oven has not been heating to any proper temperature Does not seem to reach the set temperature Any help please- urgent Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 725 Answers

Check your elements are they red?

Posted on Aug 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Amana Convection Oven - Not heating in normal bake mode, but works otherwise


I will say that is the control board that is not working properly. Have you try to unplugged for phew minutes?, this will reset the current settings. If not, I will star replacing the control board. Good Luck!.

Jan 13, 2014 | Amana Ovens

1 Answer

Adjust thermostat


A thermostat only cuts the heating off when the temperature it is set to is reached while the heating is on. If the heating is set to off then the thermostat will do nothing.
Generally you want to think about when you want your heating to come one and off by using the timer and then the thermostat is just used to ensure that you don't waste energy by exceeding the maximum comfortable temperature.

Hope this helps a little.

Nov 22, 2013 | Ovens

2 Answers

Temperature does not always reach set point of 425 F.


Oven will not hold correct temperature:------- This can be caused if temperature probe not working.Resistance across temperature probe leads at room temperature (70°F) should be approximately 1096 ohms.----------- Other possibility for this problem is :--- Temperature control not calling for heat.When heat is required, there should be continuity between terminals 6 and 7 on temperature control.-----------Inadequate or improper ventilation.Check ventilation hood. Verify draw and make up air adjustment.-----------If all this checked out ok then its calibration problem.For calibration follow this procedure:--
It can be problem with temperature controller. TEMPERATURE CONTROLLER (Standard-Control Models Only) The calibration of the temperature controller should not be changed until sufficient experience with cooking results has definitely proved that the temperature controller is not maintaining proper oven temperatures. Before any recalibration is attempted, the oven temperature should be checked by the following procedure: 1. Remove all trays and pans from the oven. 2. Place a thermocouple or a reliable mercury oven-type thermometer at the center of the middle rack. 3. Turn the oven ON and set the temperature control knob to 400°F. 4. The amber "heat on" light will go out when the oven temperature is reached. 5. Allow three cycles for the temperature to stabilize. 6. Read the thermocouple or thermometer immediately after the light goes out for the third time, and again immediately after it comes on the next time. 7. If the average of these readings varies by more than 10°F from the dial setting, recalibrate by the following procedure. Recalibration should be attempted only by a competent service technician. Use the following procedure to recalibrate the oven: 1. Loosen the two set screws that secure the temperature-control knob to the temperature-control shaft. 2. Remove the knob from the shaft, being careful not to rotate the knob or shaft. 3. Replace the knob on the shaft so that the indicator mark on the knob points directly at the temperature that was measured at the center of the oven. 4. Re-check the oven calibration. ----------- Part number for temperature probe is 1181996 and you can order if from the Southbend service center. -------- If you want the manual and wiring diagram for your oven.Please click the link directly:-- http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man ----------- after you click the link,a page will open in that you fill the 5 letter number.And click the "download now " option.It will ask you to save or discard.Click the save option and download will start.It will take 2 mins to download.Then click the download file to open it.And go through the manual.------------This will help.Thanks.Helpmech.

Jan 28, 2011 | Southbend ES10SC Electric Single Oven

1 Answer

I have a Competence 52081 double oven. Ity has


Thermostat may need adjusting OR air may be entering the oven causing the problem

Sep 01, 2009 | Ovens

1 Answer

Amana Electric Oven Issue


My oven never reaches the proper temperature sitting for baking. Controls for the oven only is push buttons. How can I adjust this. This has been going on since I have bought the Amana

Oct 27, 2008 | Amana AOCS3040 Electric Single Oven

1 Answer

Gas oven won't maintain temp. It turns off after reaching temperature set.


Hi ya mate sorry to hear your having problems with you oven,

The problem wiht your oven seems to ba a faliure of the fsd/ffd, it seems to me that this device is not completey gone but is faulty.

This device is used as a safety feature on gas ovens and is there to turn the gas off to the oven when the flame has failed.

The way it works is that the intial small flame heats up the the phile at the end of the cappliary tube which is connected to a valave which realses the gas to the oven..


what you need is to have it change


hope this helps

washdoctor

cheers

Aug 28, 2008 | Ovens

1 Answer

NEFF Oven Model B1430NOGB/02 Oven Temp not heating above @50 degrees


probably the element. to save wasting money, check continuity with a multimeter

Jun 25, 2008 | GE Profile JT912 Electric Single Oven

1 Answer

Pepper Oven overheats


This problem is caused by a faulty thermostat controller. This is the dial that you use to set the temperature for heating.

Jun 17, 2008 | Fisher and Paykel Ovens

Not finding what you are looking for?
Neff U1661 Double circotherm super Electric Oven Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Neff Ovens Experts

bosch5

Level 2 Expert

157 Answers

paulcarew

Level 3 Expert

2047 Answers

xxxxxx xxx

Level 3 Expert

4724 Answers

Are you a Neff Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...