Question about Torin Big Red Hydraulic Shop Press with Gauge Dial 40Ton

1 Answer

The hydraulic hose connector is broken. Can't find a manual or parts list.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,422 Answers

You can get that hose made at a place like NAPA . The hose is a couple of dollars a foot and the fittings are about 10 a peice Bring the old one with you it takes 10 munites to make

Posted on Mar 14, 2011

  • JOHN LAPIER Mar 14, 2011

    I belive you mean the fitting on the hose . But if not they also have fittings so bring what you need and they should be able to match it up I used to owen a cheery picker and got all hoses and fittings there noproblem

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where I can get 1993 infinity j30 power steering pressure hose or it compatible part at low cost?


low cost will be from a wrecker that handles your make of car
hydraulic hose shops can manufacture one if you provide the sample
that will be about 1/2 cost of a genuine hose
genuine as a last resort

Oct 03, 2015 | Cars & Trucks

1 Answer

Peugeot 308 service manual 2008


the parts needing attention will be listed in the service schedule of the book. They will include timing belt, transmission filters ,belts, hoses, hydraulic fluids, power steering filter along with all the other consumables used for a service.

Dec 29, 2013 | Cars & Trucks

1 Answer

I have a leaky power steering hose, the leak starts by the second crimp.What kind of hose and fittings do I need to replace it.


Your best bet is to get the hose assembly from the Auto parts store. Those are high pressure hoses made of special material that are resistant to the corrosive nature of Hydraulic fluid and the pressure that builds in those lines. The connections where the hoses connect to metal connectors are compression fittings and difficult to replace under the best of circumstances. When you identify the parts you need Auto Zone and Advance Auto can show you the parts diagram so you can make sure you get the correct line.

Sep 23, 2011 | 1997 Honda Accord

1 Answer

I have a 2003 protege dx.I had no problems till today I pepressed the clutch pedal and it went to floor and did not come up.After looking under hood I could see where a hydraulic hose on lower driver side...


U have a broken hose, replace the hose . Take the broken hose to a parts dealer. Refill the master cylinder that powers the hose,with the proper fluid. One end of the hose will screw into master cylinder.

Sep 21, 2011 | Mazda Protege Cars & Trucks

1 Answer

Need parts list for a Dayton Model 3ZC69


icon_alert_large.gif JavaScript Disabled Your web browser does not have JavaScript enabled.
In order to use most of the functionality of this website, you will need to have JavaScript
enabled in your browser. icon_alert_large.gif Browser Cookies Are Disabled Your web browser does not have Cookies enabled.
In order to use most of the functionality of this website, you will need to have cookies
enabled in your browser. document.getElementById('javascriptAlert').style.display='none';if (!cookiesEnabled) {document.getElementById('cookieAlert').style.display='block';} Repair Parts Info > Parts List

There are 25 parts listed below for: Manufacturer/Brand: WESTWARD Model #: 3ZC69 Description: Ram System 10 Ton Additional Model Info:
Find Out More About This Product

Be sure you have the right model. Match the Additional Model Infoicon_help.gif (above) to your unit's nameplate/label. pixna.gif
spacer.gif View Printer Friendly Parts List icon_printerfriendly.gif Sort Table By: spacer.gif Sort ByManufacturer Part #DescriptionRef. # spacer.gif function sort_func(){ var sby = 'http://www.grainger.com/Grainger/rp_parts_list.jsp?xi=xi&lastMfgSearchCriteria=&lastModelSearchCriteria=&lastInfoSearchCriteria=&lastProdSearchCriteria=7142866&lastSuppSearchCriteria=&sort=' + document.partsList.sortBy.value ; document.location.href = sby ; } var hexVals = new Array("0","1","2","3","4","5","6","7","8","9","A","B","C","D","E","F"); var unsafeString = "\"%\\^[]`&#"; function popWinAdditionalModelInfo() { var page = 'http://www.grainger.com/Grainger/help_add_modelinfo.jsp?xi=xi'; var popupwindow = window.open(page,"help_add_modelinfo","width=400,height=350,menubar=no,scrollbars,status=no"); popupwindow.focus(); } function popWinNotAvailable() { var page = 'http://www.grainger.com/Grainger/help_not_available.jsp?xi=xi'; var popupwindow = window.open(page,"help_not_available","width=400,height=350,menubar=no,scrollbars,status=no"); popupwindow.focus(); } function URLEncode(val) { var len = val.length; var backlen = len; var newStr = ""; var frag = ""; var encval = ""; for (var i=0;i= radix) { temp = num % radix; num = Math.floor(num / radix); hexString += hexVals[temp]; } hexString += hexVals[num]; return reversal(hexString); } function reversal(s) { var len = s.length; var trans = ""; for (i=0; i 32 && compareChar.charCodeAt(0) spacer.gif Manufacturer Part # spacer.gif Description spacer.gif Ref. # spacer.gif Parts
Diagram(s) spacer.gif 234-4-1900-208 Filler Screw 426-3-1303-203 Release Valve Knob &threaded Stem 435-01 Extension, 28 3/4in 435-02 Tube, Extension 19 3/4in 435-03 10in Extension 435-04 5-3/4in Extension 435-06 Male Connector 435-07 Wedge Head 435-08 Serrated Saddle 435-09 Flat Base 435-10 Ram Toe 435-11 Plunger Toe 435-12 2-3/4 Flex Head 435-13 90 Degree Combo Head 435-14 Hydraulic Spreader 435-15 Hose Dust Cover 435-16 Ram Dust Cover 435-17 Hose Coupler 435-18 Ram Coupler 435-22 Pump Handle 435-23 Hose 435-25 Pump Assy 435-27 Plastic Case 435-3-9908-101 Pump Repair Kit F100-30000-000 Ram Plunger spacer.gif View Printer Friendly Parts List icon_printerfriendly.gif

Jun 20, 2011 | Garden

1 Answer

Location of blower resistor on 2003 grand marquis?


Hello, Just follow the wire from the heater fan under the hood. Trace the power wire from the heater fan and it will join a connector midway on the Firewall. It will have 2 screws and 1 electric connector. Tap the connector with a screwdriver handle and see if the part starts working again.

If it does not, get a used or new blower resistor. Work on a cold engine and remove the screws and connector from the part. Temporarily plug in the new part to the connector and turn the Key to run with the fan ON. It should be blowing now. Turn off the switch and put the new part where you can reach it with 1 hand.

Undo a heater hose at the top rear of the motor going in front of the opening for the switch. With 1 hand remove the hose end, then switch parts with the new blower resistor with the other hand and slide the heater hose back on its fitting. Tighten the heater hose.

Then secure the new part into the Firewall and fasten its connector. You should have lost little Antifreeze by working on a cold engine as the hydraulic lock kept the fluid from running out.

This should be all you need to do except clean any spills away.

May 22, 2011 | 2003 Mercury Grand Marquis

1 Answer

I have a 1992 Crysler Imperial. The ABS light is on and the ABS pump runs all the time. Help.


Either the ABS Module is bad or the Pump is bad--- Pump REMOVAL & INSTALLATION 1989-90 Models
  1. Disconnect the negative battery cable. Depressurize the hydraulic accumulator. CAUTION
    Failure to depressurize the hydraulic accumulator, prior to performing this operation may result in personal injury and/or damage to the painted surfaces.
  2. Remove the fresh air intake ducts.
  3. Disconnect all electrical connectors to the pump motor.
  4. Disconnect the high and low pressure hoses from the hydraulic assembly. Cap the spigot on the reservoir.
  5. Disconnect the shift selection cable bracket from the transaxle and move it aside.
  6. Loosen the nuts on the 2 studs that position the pump/motor to the transaxle differential cover.
  7. Remove the retainer bolts that are used to mount hose bracket and pump/motor. The engine inlet water extension pipe is also held in position by these bolts. NOTE: Do not disturb the inlet water extension pipe, or engine coolant will leak out.
  8. Disconnect the wiring harness retaining clip from the hose bracket.
  9. Lift the pump/motor assembly off of the studs and out of the vehicle.
  10. Remove the heat shield from the pump/motor, if equipped and discard. To install:
  11. Place a new heat shield onto the pump/motor bracket, using fasteners provided.
  12. Install the pump/motor assembly onto the studs.
  13. Install the wiring harness retaining clip onto the hose bracket.
  14. Install the retainer bolts to the hose bracket and pump/motor. Tighten securely.
  15. Tighten the 2 nuts until secure.
  16. Install the shift selection cable bracket onto the transaxle.
  17. Connect the high and low pressure hoses to the hydraulic assembly and tighten to 13 ft. lbs. (17 Nm).
  18. Attach all electrical connectors to the pump/motor.
  19. Install the air ducts.
  20. Readjust the gearshift linkage, if it was disturbed.
  21. Connect the negative battery cable and check the assembly for proper operation.
1991-95 Models
  1. Disconnect the negative battery cable. CAUTION
    Failure to depressurize the hydraulic accumulator, prior to performing this operation may result in personal injury and/or damage to the painted surfaces.
  2. Depressurize the brake system.
  3. Remove the fresh air intake ducts from the engine.
  4. Remove the clip holding the high pressure line to the battery tray.
  5. Disconnect the electrical connectors running across the engine compartment in the vicinity of the pump/motor high and low pressure hoses. One of these connectors is the one for the pump/motor assembly.
  6. Disconnect the high and low pressure hoses from the hydraulic assembly. Cap or plug the reservoir fitting.
  7. Disconnect the pump/motor electrical connector from the engine mount.
  8. Remove the heat shield bolt from the front of the pump bracket. Remove the heat shield.
  9. Lift the pump/motor assembly from the bracket and out of the vehicle. Fig. 1: The pump/motor assembly mounts to the top of the transaxle case and is covered by a heat shield 86729g75.gif
    To install:
  10. Fit the pump motor assembly onto the bracket; install the heat shield and its retaining bolt.
  11. Install the pump/motor electrical connector to the engine mount.
  12. Connect the high and low pressure hose to the hydraulic assembly. Tighten the high pressure line to 145 inch lbs. (16 Nm). Tighten the hose clamp on the low pressure hose to 10 inch lbs. (1 Nm).
  13. Connect the electrical connectors which were removed for access.
  14. Install the high pressure line retaining clip to the battery tray if it was removed.
  15. Install the fresh air intake ducts.
  16. Bleed the brake system.
prev.gif next.gif

Oct 07, 2010 | 1991 Chrysler Imperial

1 Answer

Washer hose connector is broke can this be repaired


First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

You should be able to see a number of hoses, connectors etc that will replace your broken connector.

Mar 30, 2010 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

ISUZU WAS IN AN ACCIDENT. THE PLASTIC HEATER HOSE


Strip it back and replace all the broken items/parts. New or good clean used parts. You do it or pay a repair shop. What is the problem or question. It is broken Fix it

Sep 26, 2009 | 1999 Isuzu Rodeo

1 Answer

Brake line diagram


Brake Lines and Hoses
Double-walled steel line is used in the hydraulic lines between the brake master cylinder and the front tube connector, and between the brake master cylinder and the flexible brake hose at the rear wheels.
Double-flared brake lines provide good leak-proof connections.
When replacing hydraulic brake lines, hoses, or connectors, tighten all connections securely. After replacement, bleed the brake system; refer to Section 206-00 .
The wet appearance of the outer cover of the rubber brake hose is referred to as "sweating." This is a normal condition for neoprene rayon braid hose and is not a sign of leakage or cause for replacement of the hose.

Hydraulic Brake System Components — Non-ABS

dff7165.gif
Item Part Number Description 1 2005 Power Brake Booster 2 2455 Brake Pedal 3 2261 Rear Wheel Cylinder 4 2552 Rear Disc Brake Caliper— (Mexico Only) 5 2B120 Disc Brake Caliper—, Front 6 2B091 Brake Pressure Control Valves 7 2140 Brake Master Cylinder

May 02, 2009 | 1998 Mercury Tracer

Not finding what you are looking for?
Torin Big Red Hydraulic Shop Press with Gauge Dial  40Ton Logo

Related Topics:

803 people viewed this question

Ask a Question

Usually answered in minutes!

Top Torin Big Red Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1383 Answers

Joe Garcia
Joe Garcia

Level 2 Expert

205 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Torin Big Red Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...