Question about Computers & Internet

3 Answers

What would username and password on login setup for Linksya wireless router?

Posted by on

  • Cvb Brown
    Cvb Brown Mar 15, 2011

    No it asking for another password in settings

  • Larry Fostano
    Larry Fostano Apr 18, 2014

    Do a factory reset,press and hold reset button on rear of router for 30 seconds with power applied,without removing finger from button unplug power the in 30 seconds apply power all done without removing finger from reset button.When you complete these steps you router will default to factory and you will be able to use your router again.

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 55 Answers

Factory default password and username
User: leave it in blank Password: admin
or
User: admin Password: admin

Posted on Mar 14, 2011

  • Alejandro Hernandez
    Alejandro Hernandez Mar 14, 2011


    factory default password and username


    User: leave it in blank

    Password: admin



    or




    User: admin

    Password: admin

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 902 Answers

Most linksys routers are as follows
user name admin
password none
username none
password admin

Posted on Mar 14, 2011

  • Larry Fostano
    Larry Fostano Apr 18, 2014

    Do a factory reset,press and hold reset button on rear of router for 30 seconds with power applied,without removing finger from button unplug power the in 30 seconds apply power all done without removing finger from reset button.When you complete these steps you router will default to factory and you will be able to use your router again.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 27 Answers

On newer linksys routers the username and password are both "admin" (no quotes). On older ones I think the username is just left blank and "admin" is the password.

Posted on Mar 14, 2011

  • X5494 Mar 16, 2011

    If you're logged in to the router, it's probably wanting you to change the default password to login to the router. If you're on the wireless settings page, it's asking you to set a password to limit access to your network.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My edimax wireless access point is saying i have the wrong username and password and wont let me login


For most Edimax routers, the default IP address is 192.168.2.1, default username is admin and password is 1234.
By default the router is a DHCP server which will assign IP address starting from 192.168.2.100 to 192.168.2.199 to DHCP clients automatically.
Make sure your computer has TCP/IP Protocol setup as "Obtain IP address automatically".
Open the Internet Explorer.
Type in http://192.168.2.1 hit Enter.
The Login window will appear.
Type in the default username admin, password 1234.
Click on Login.
Then you can configure the router.

Sep 11, 2013 | Edimax Computers & Internet

1 Answer

I LOST INSTALLATION CD FOR MY D-LINK DIR-600


->Download the manual from the router website and find the username and password,if you don't no the default password.Then reset the router to go for default login.

->Most d-Link routers have the IP address of 192.168.0.1 login using username and password.
->After login select "Manual Wireless Network Setup" from setup tab.
->Your basic wireless network settings are in this screen. First, give your wireless router a name that you can recognize it by. Secondly, select a type of Security Mode. WEP-Personal should be efficient for most people's usages. After that is selected a new window at the bottom appears.Type your password in the Pre-Shared Key, scroll to the top and hit save, and that's all there is to it.


If you need any kind of technical assistance on router, you can contact support cell at http://www.vtechsquad.com/

Nov 07, 2012 | D-Link DIR-600 Router

1 Answer

Need password for wireless roter


If you need the login password for the router's setup page, the default username: admin, password: password.

11_20_2011_11_23_47_am.png
If you need the wireless key or password, you need to access the router's setup page by typinghttp://www.routerlogin.net or 192.168.1.1 in the address field of your browser(IE or Chrome). On the login use the default username and password(admin, password).
After logging in. Look at the main menu on the left, click on Wireless Settings, from there you can check the WEP or you can setup wireless security from there if you haven't done so.
11_20_2011_11_27_44_am.jpg
**If by chance you are unable to access the router's login or setup page, you will have to reset the router to factory settings by holding the reset button on the back of the router using a paper clip or a pen for 30 seconds while the router is plugged in to the power outlet. You will then be able to access the router's setup page using the default username and password.

Hope this helps.

Oct 16, 2011 | NetGear WNR2000 Wireless Router

1 Answer

I lost my pin


If it is the pin of your encrypted wireless connection (WEP/WPA etc.) then go to router's login page , usually 192.168.1.1 and then login using your admin username and password. In case you had not setup the router yourself then try the following username password combinations :
Username : admin password : admin OR Username : admin password : password
If you are able to login , then you can simply give a new password to your wireless connection . Exact instructions for doing so vary with the make of the router . In case if this doesn't work then you can try doing a hard reset of your router by pressing the corresponding button . Check in the manual of your router for doing so . In case you don't have the manual , then post the Model Number / make of the router or try searching for the manual on the internet or post back the model number for more detailed instructions.

May 09, 2011 | Computers & Internet

1 Answer

Where is password on this box


I assume you mean the login password for the box.

Depending on the version of the Box, the default password / login combination is this:


Username: Admin
Password: password

OR:


Username: Admin
Password: setup

OR:


Username: Admin
Password: 1234


If however, the password has been changed at some time, you will have to reset the router using a paperclip. THIS WILL RESET ALL SETTINGS so use as a last resort.

Mar 15, 2011 | NetGear WGR614 Wireless Router

2 Answers

Forgot my wireless internet password


Hi,

You have to login to router ,for wireless password
following is the way to login to router

1. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
2. Access the router, usually by typing 'http://192.168.1.1' or 'http://www.routerlogin.com' in the address bar.
3. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
4. Click on Wireless Settings'(under Setup) from the left menu.
5. If WPA is selected in Security mode, then check the Password that show up in the passphrase box.


Hope it can resolved your issue
please rate the service if issue resolved
Thanks for using Fixya

Apr 04, 2010 | NetGear WGR614 Wireless Router

1 Answer

My itouch says its connected but wont open any webpages


Please follow the steps below to login to the router page and check the network key:
make sure that other wireless device is working fine,if it is working fine then you can try these steps

1. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
2. Access the router, usually by typing 'http://192.168.0.1' or 'http://www.routerlogin.com' in the address bar.
3. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
4. Click on Wireless Settings'(under Setup) from the left menu.
5. Changed SSID(network name)and changed security
6. click on wireless setting'(under advanced)
7. click on SETUP ACCESS LIST (Turn Access Control On)it should be unchecked
then try to connect wirelessly
regards
prakash

Mar 11, 2010 | NetGear DG834G Router

1 Answer

Can not get my wii console to connect to my wireless router. It is a belkin and it keeps asking for a password.


To login to router setup page you need to connect the router with a ethernet cable to one of your computer or laptop then open a page of internet explorer and type in browser address bar http://192.168.2.1 and it will ask for username and password the username is by default "admin" and password is blank do not type anything in password and press ok you will go to the page of the router

  1. Then go to wireless settings and you can check what is the wireless security password, you can use the same to connect your wireless computer to your router to access internet wirelessly
  2. If you are not able to login to router setup page then you might need to reset the router from the reset button
Please let me know if this will help

Jan 06, 2010 | Belkin Wireless Pre-N (F5D8230-4) Router...

1 Answer

Linksys setup


That's because you have to enter the username and password in order to access/change the security features of this router. There are default login/password entries required for security access within the router, even when it's set back to original factory settings.

Check your user manual for the default login information.

Aug 28, 2009 | Linksys Wireless-G WRT54G Router

1 Answer

Please does anyone know the password for the belkin wireless g plus router version 1212uk please help


Which password do you ask? Router's password or wireless security password? For the router's password, by default it is admin in lower case. No username. If you are asking for the wireless security password, you need to login to the router's setup page and get the wireless password

Jun 20, 2009 | Belkin Wireless G Plus MIMO (F5D9230-4)...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

703 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...