Question about Weiser Lock POWERBOLT ELEC DEADBOLT

1 Answer

No sign of life at all. No beeps, no motor twitches, nothing. Up to now worked fine. It is not just the batteries.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 963 Answers

Here is a link to troubleshooting your powerbolt lock. You will find the problem problem of beeping (or no beeping) addressed here:

There is a link at the top of this page for Customer Support from Weiser.

Good luck!

Posted on May 13, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I fix no power light or start up?

Disconnect the AC power.
Remove the battery.
Press the ON/OFF button to "drain" any residual power.
Open the cover over the RAM slots.
Remove the sticks of RAM, and then re-insert them.
Reconnect the battery.
Press the ON/OFF button.
Does it still beep?
If so, then the CPU or graphics adapter or motherboard is the source of the problem, and you're stuck -- none of these parts are replacement without a certified computer-technician.

May 11, 2015 | Dell Inspiron 15 (N5050)

1 Answer

Fisher and Paykel GWL11 Top Load Washer starts but drum won't turn, it twitches and beeps then turns off with solid beeps

Hi ken
Can you turn the bowl & agitator by hand.
If it can't turn by hand, Your seal & bearings need replacing.

Feb 01, 2013 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

I have a Samsung TL100 camera and it will not take a charge

If you haven't used it for the last 8 months and before it was all fine then the most common reason would be the battery. Your battery is absolutely dead but then again if you plug it to AC then it must show some sign of life. But give it a go by replacing new battery. To check get it from a friend and then test the camera on it.

If the battery replacement doesn't work then take it to an authorized dealer for inspection.

Oct 30, 2012 | Samsung TL100 Digital Camera

2 Answers

My pc just chirps but does not turn on It is a k8 upgrade 1689 mother board 1 gb drr ram geforce6800 graphics card 3200+ amd athlon processor it was all working fine then i tried to boot up this moorning...

sounds like your motherboard has hard it try dissconnecting the everything exept CPU power supply keyboard and screen and see if you can get it to come up with the bios, if it still dosnt work unplug the fan on the CPU and turn it on then see if that works (dont leave for more than 1min without the heatsink fan spinning as it can cause the processor to overheat anything less than a min you ok. just long enough to see if theres any signs of life on the screen. hope this helps

Sep 23, 2009 | Asrock K8Upgrade-1689 Motherboard

1 Answer

HP nx 7300

remove and, reinstall the memory...If that doesn't work disconnect each device i.e. DVD, wireless nic etc. repowering each time.

Aug 25, 2009 | HP Compaq nx7300 Notebook

1 Answer

Hyundai Tiburon Won't Start

Possibly the alarm cut-off switch? or Ignition key switch (or wires) going bad?

But you mentioned you tried to jump start it and it did turn over?
IF so, you could have severe corrosion or loose connections of the battery cable both at the battery and at the termination points, such as ground and starter motor.
Check that the battery wires are tight and clean at the battery posts and at the other end.

Again the No lights suggests either the alarm cut-off, or an absolute disconnected battery cable.

Finally, it could be ignition fuse, Check fuses. Ignition key switch.

What makes this hard is that you suggest it would turn over with another battery connected. This makes no sense.

Good luck

Mar 16, 2009 | Hyundai Motor 2000 Tiburon

2 Answers

Shutter problems

sean baker,
If the camera was working when you stored it and the shutter fires occasionally, it's probably battery corrosion. Clean the contacts with a pencil eraser,or contact cleaner tool.
What kind of camera ?

Sep 09, 2008 | Pentax MZ-50 35mm SLR Camera

1 Answer

Phone wont switch on

dont upsate friend, i have one solution for u. but i cant say surely to work it. Remove your old batteries and try to insert any usable battery of another same mobile friend and try to check. i think that is battry problem. Or If that not done so go to any nearest Mobile Repair shop.

May 03, 2008 | Nokia 2310 Cellular Phone

1 Answer

3 beeps at start

hmmm...that's not good. works fine with no battery. I suspect your motherboard may be taking a vacation from working soon.

got backup for your HP?

Feb 12, 2008 | HP Pavilion dv2000t 14.1" Notebook Laptop...

Not finding what you are looking for?

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

1889 Answers

john h

Level 3 Expert

12650 Answers

Cindy Wells

Level 3 Expert

5159 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides