Question about GPS

1 Answer

Where can i get a manual? the engine on liftmaster 1265-267 clicks but no longer moves.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers


Posted on Mar 14, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Drive/worm gear on liftmaster garage door opener is worn out and no longer driving the chain to open the door. Apparently this gear is a common part and looking for detailed steps on how to replace it...

You did not specify the model of your door opener: However if you got the LiftMaster website you should be able to locate an Owner's Manual for your door opener.

Go here, select your model or series and then on the next page at the bottom right should be a link to the Owner's Manual.

The manual includes schematics, including the assembly of the motor unit.

You might find these illustrated instructions on similar product to be of use.

Jan 15, 2011 | Computers & Internet

1 Answer

Hi I have a liftmaster garage door opener. It has been stopping alot during the opening and closing process. Nevertheless, it has continued to work. Now when I hit the main button on the wall,...

There are a couple of different models out there but they are all pretty much the same. Have you tried running the operator with the door being in manual mode? If you have not, push the wall button and see if the operator does anything.

If the operator runs fine without the door attached then try this:

Look for 2 blue tear drop shaped knobs, if you have a one light bulb or a 2 light bulb front and back those knobs will be on the back. If you have a 2 light bulb side to side, the knobs will be on the right side (right next to where the wires hook in to the operator). Turn the knobs slightly clockwise. The door should then move. If it moves more than it did but still stops, tweak them just a little at a time.

Let me know if this helps or not.

Sep 11, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

All of a sudden my garage door motor will not run, only clicks when pressing wall button or remote. garaage door moves manually.

Sounds like the trolley is stopped up against the stop bolt on the rail. This comes from bad limits. This happens often on older Chamberlain/Sears/Liftmaster etc openers.

Jul 16, 2010 | General Electric GE 13-438 Overhead Garage...

1 Answer

My Liftmaster GDO makes a clicking sound and won't open

See if the trolley is jammed against the bolt just in front of the motor unit. If so remove the bolt and then run the opener until the door is closed. While the door is closed locate the 'up limit' control which is on the side of the motor unit. Turn this control 2 complete turns in the opposite direction of the arrow printed on the cover. Remember to replace the bolt.

Jan 09, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Need to change my remote code after divorce

Follow this link for the manual and look on page for programming.

Dec 16, 2008 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Liftmaster 1265LM 1/2 HP does not open or close with remotes

is chain moving. if not, gears are shot. if moving, is trolley connected.

Dec 10, 2008 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Craftsman 1245LM reprogram

The keypad outside has manuals online that you could use, but for simplicity, Have someone go to that back of the machine and press the "Learn" button, once its is pressed, the yellow light should blink. Enter a new code (4digit) into the keypad and press the enter button. You should then hear a click and the lights on the machine should flash. That will program your keypad.

Sep 16, 2008 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Arm won't move





Feb 09, 2008 | Sears Craftsman LiftMaster Chamberlain...

Not finding what you are looking for?
GPS Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top GPS Experts


Level 3 Expert

79865 Answers

Will Halftowaite

Level 3 Expert

508 Answers

The Knight
The Knight

Level 3 Expert

75417 Answers

Are you a GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides