Question about Power Acoustik Car Audio & Video

1 Answer

I accedently conected the power cabel on the ground conector and the graund on the power n now it dont turn on it blows my fuses

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 391 Answers

Hi at the rear of the amp where the power terminals are open it and where the power terminals conect to the circuit board you will see a black diode this is what we call a dummy or a reversed diode you will have to remove this and replace it if you dont and this happens again there will be more serious damage done and may be unrepairable let me know how you get on

Posted on Mar 14, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


I would think that either the power wire feeding the pump or the pump itself is grounded and causing the fuse to blow. Pulling the injector relay is opening the circuit and not feeding power to the pump would be why it doesn't blow the fuse when it is removed.

Aug 12, 2015 | 1999 Mazda 626

1 Answer

05 road glide running light works but every time I turn the ignition on it blows the brake light 15amp fuse

Hi Peter, you have a broken or exposed to to ground power wire. Get out your test lite and connect it to the power side of the fuse clip. Start at the tailight stabbing wires, conector block pins, ect. and work your way towards the front and rear brake light switches. When the test lite glows then you are very close to the problem. The web site below may assist you with a wiring diagram that comes close to your year and model.
Good luck

Apr 26, 2015 | Harley Davidson Motorcycles

1 Answer

Why burning 44608p40 power supply k2645

Check ground screew , also disconect and re conect conector .

Jan 17, 2015 | Power Computers & Internet

1 Answer

Daytime running lights and headlights dont work and horn blows randomly

disconect battery wait few minuts re conect see if problem gos away if not the body controll modual might have water in the conector or has failed

Mar 06, 2014 | 1998 Dodge Grand Caravan

1 Answer

Sir my lephone c2 isdead pleas telle how it can be repair

first cheak + & - line in curcuit
cheak out R22 countinutiy
cheak countinuty of. bettery conector
if you find any problam of as abov then
use jumper
( - ) for graund
( + ) for charging + point
it's simple try it

Jun 23, 2013 | Cell Phones

1 Answer

I have a fuse that keeps blowing and the white letters are gone so i dont know what it goes to

you have some componet that has melted down contacts (it's hotwire is grounded) so every-time u turn on the key power is fed to direct short and the fuse blows.So look around at things that dont work.after fuse blows does motor still operate,keep it running and find out what doesnt work then check that component for melted,grounded wires...

Dec 27, 2011 | Cars & Trucks

1 Answer

The car is turning over but will not start and run

chek the gasoline pump in the tank souns like its not working open the trunk and in front off the spare tire under the floor carpet you will se a litel plate that is bolted whit 2-4bolts thake them out and lift the plate and ther is going tho be a cabel and the cabel is conected tho the pump thurn on the ignition and att the same time listen tho were the cabel is conected if it works you are going tho here a small buzzz if you dont its ded

Oct 20, 2009 | 1996 Nissan Maxima

1 Answer

Right turn signal flashes fast and all rear and front

your tail light has no graund. usualy plastic conector no the lamp melt down around ground cable

Aug 31, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Starter turns over but does not engage

One of 2 things. The part on the end of the starter called a bendix is bad (most likely and less expensive) or the ring gear that the bendix engages is bad. (less likely MORE expensive). If you are comfortable with the work try locating a starter locally and replace it yourself.

Aug 02, 2009 | 1997 BMW Z3 Roadster

1 Answer

Dual xpa 4100 2/3/4 chanel amp

make sure power and ground are where they are suppose to be and speaker wires are not mixed up. but it sounds to me like the amp is junk

Jun 09, 2008 | Dual 2-Channel Bridgeable MOSFET Amplifier...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Power Acoustik Car Audio & Video Experts

Tygh Duval
Tygh Duval

Level 2 Expert

300 Answers


Level 3 Expert

76846 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Power Acoustik Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides