Question about Kenmore 23313 Whispertone Bagged Canister Vacuum

1 Answer

Kenmore Whispertone 100 connection issues

We have a Kenmore Whispertone where the connection between the handle and shaft is constantly loose causing the unit to go on and off with each pass of the sweeper. I tried adding some tin foil to lessen the gap and that worked for a few months now I'm back to the same problem. Any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 125 Answers

Find a used one at a vac repair shop, its just worn out

Posted on Dec 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doesn't turn on


Gain access to the electrical connection with voltmeter set to 110 v ac check for voltage on both sides of switch. If voltage is present on outlet side follow output wire to start relay ck for power on out put side of relay. if power follow output wire to motor if voltage is present replace motor ! Be careful where you touch when probing contacts !

Dec 29, 2012 | Kenmore whispertone 100 model 116

1 Answer

Rollers not moving


A careful inspection is likely to reveal the belt that moves the rollers is broken or the rollers are jammed up with hair or fiber and cannot move---the jammed up issue usually requires no real tools but the belt will require that are where the rollers are to be opened up to get at the belt which usually slips on the shaft from a motor---tight fit.

Dec 17, 2012 | Kenmore 23313 Whispertone Bagged Canister...

1 Answer

Was using kenmore whispertone stopped suddenly disconnected brush unit will not switch on ????


if you took the hose out of the wand assembly then it may not turn on as the hose handle has a power button on it and must be connected to turn on the unit.Also check the powerhead for a reset button (small red / or black button on the back of the head){back of head not the bottom}

Oct 05, 2010 | Kenmore 23313 Whispertone Bagged Canister...

1 Answer

Sears Kenmore Whispertone Vacuum Problem:


If you push inwards on each side of the light cover on top you can remove it. With the light cover removed remove the (2) access screws. Now you will be able lift of the entire top cover from the base. You will then see the belt and roller brush, remove the old belt and replace with a new one. You can get the replacement belt you need here:

Kenmore Whispertone Replacement Belt

Oct 28, 2009 | Kenmore 23313 Whispertone Bagged Canister...

1 Answer

Belt keeps breaking.


your brush roller isn't turning unplug the vacuum and see if you can turn the brush roller and also notice if it turns freely or is it stiff,take the roller out and remove strings,carpet strands and hair.if you can pull the ends off clean the ends good and maybe add just a little drop of machine oil on the bearing on the inside the roller where the bearings are.clean the motor shaft.there is probably old burnt rubber on the motor shaft.you can use a pice of emery cloth ,clean it till you see the polished finish .but i would say your problem is in the brush roller and the motor shaft.i hope i was some help to you.can you please leave some feedback

May 03, 2009 | Kenmore Whispertone 29512 Vacuum

1 Answer

Power head for Kenmore Canister Vac


Another potential problem for the increase in difficulty in turning the beater bar (drum) could stem from extremely dirty bearings, located at each end of the beater bar. I've seen hair knotted up to the point it chokes the bar and significantly reduces its ability tpo turn.

Mar 11, 2009 | Kenmore Whispertone 29512 Vacuum

1 Answer

Motor goes on and off briefly at regular intervals


Sounds like you may have a bad or loose connection, could be one of wires in the hose to the handle harness or the harness itself may be causing the problem. Also be the motor or relay causing a problem.

Jan 08, 2009 | Kenmore 23313 Whispertone Bagged Canister...

2 Answers

Whispertone powerhead handle release replacement


Use a flat blade, it just prys off, a new on will press on.

May 24, 2008 | Kenmore 23313 Whispertone Bagged Canister...

1 Answer

Kenmore whisper tome model # 116


If this uses a cogged belt, it should not fall off unless it is the wrong one. Give me the whole model #, then I can look and see what you have. The number of the power head is needed.

May 23, 2008 | Kenmore 23313 Whispertone Bagged Canister...

Not finding what you are looking for?
Kenmore 23313 Whispertone Bagged Canister Vacuum Logo

Related Topics:

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

Roger Potts

Level 3 Expert

694 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Kenmore Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...