Question about Televison & Video

1 Answer

I have a SAMPO PME 42-3 Plasma TV. I turned it on this morning and got a "SYSYEM IMFORMATION" blue screen and at the bottom of the screen, It has some codes and "FACTORY RESET DONE" I can't get this to disapear. Can you help me figure, why I have this screen and more importantly, how to get it to disapear? The screen detail from top to bottom: SYSTEM INFORMATION Model N/M/S America REGION NO 1 SDK VER 808807bf LOADER VER DVDRRW GDA-4164L SD53 CPRM CHECK CPRM KEY --- OK I/O MICOM 80625_0 EVID TOUCH :00 <usb:ng> Checksum :1462 FACTORY RESET DONE Thank You Clay

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,140 Answers

Hello Clay,

Sounds like you may have pressed the RECALL button on the remote. This restores the monitor to the factory default settings.

I would suggest disconnecting the power supply for a few minutes then reconnect the supply and switch on the monitor and whichever external video device (DVD, PC. cable/sat receiver, etc) you are using as the source for the monitor. Next, open the fold-down front panel on the monitor and press the INPUT button repeatedly until you see the picture from the external source on the screen.

The flip down panel is next to the power button/LED on the front of the monitor. To open the panel, push it in the centre and it will pop open.

If the TV is still stuck on the screen you described, try the MENU +/- buttons on both the remote and the front of the monitor and the DISPLAY button on the remote.

If the monitor does not respond to any of the above, this would indicate a hardware/component failure in the motherboard. Please try this then let me know if you need further assistance by clicking on "Add a Comment" below your question.

Does the monitor respond to the MENU +/- or DISPLAY buttons after the power has been disconnected?

Regards,
BElectric

Posted on Mar 13, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

We are looking for a base for a Sampo 42" Plasma.


I have a PME-42S6 on Ebay that has a turning on problem it is a complete unit and work good if you can get it to turn on

Ebay # 120362175465

bid on it and pick it up and there is your stand.

Bob
678-333-6746

Jan 12, 2009 | Sampo PME-42S6 42 in. HD-Ready Plasma...

1 Answer

Need a remote control for Sampo pme 42-s6 (s) TV


I have a PME-42S6 on Ebay that has a turning on problem it is a complete unit and work good if you can get it to turn on

Ebay # 120362175465

bid on it and pick it up and there is your remote control
Bob
678-333-6746

Dec 24, 2008 | Sampo PME-42S6 42 in. HD-Ready Plasma...

1 Answer

Sampo PME-42S6 doesn't turn on


Same problem red alarm led comes on you need the power supply unit it's $139.00 you can fix it your self. And gateway dont have to parts i have a phone #

Dec 13, 2008 | Sampo PME-42S6 42 in. HD-Ready Plasma...

2 Answers

Sampo plasma TV 42inch


I have a PME-42S6 on Ebay that has a turning on problem it is a complete unit and work good if you can get it to turn on

Ebay # 120362175465

bid on it and pick it up and swap parts

Bob
678-333-6746

Oct 16, 2008 | Sampo PME-42S6 42 in. HD-Ready Plasma...

2 Answers

I have good Power supply board for your Sampo 42S4 tv,


do you know if your power supply board will work for the Sampo 42S6?

If so, I am interested.

RyanHoffmeyer@hotmail.com

Sep 13, 2008 | Sampo PME-42S6 42 in. HD-Ready Plasma...

1 Answer

Blue and green lines. no color


I have the same exact tv this sounds like a previous problem that we experienced we resolved ours by plugging into a grand video console. Good luck! Tammy woodpros01@yahoo.com

Jul 23, 2008 | Sampo PME-42S6 42 in. HD-Ready Plasma...

1 Answer

"No Signal" floating notice on Blue Screen - No other picture


If all connections and the tuner have the same issue, you either have a power supply issue or a bad digital board.

Mar 29, 2007 | Sampo PME-42S6 42 in. HD-Ready Plasma...

1 Answer

Screen blanks out


A digitalizing picture is most likly a bad connection on a screen driver cable or the driver itself is intermittant or the power supply has an intermittant filter on the substain B+ line. hope this hellps.

Oct 08, 2006 | Sampo PME-42S7 42 in. Plasma EDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74482 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...