Question about Exercise & Fitness

2 Answers

I have an Elite T1720 treadmill. Recently it has become hard to start resulting in turning on and off a few times at the control panel. Today nothing seems to work. The control panel lights up and the programs can be altered but the machine will not begin to count down and consequently will not start running. Hope you can help?

Posted by on

  • 2 more comments 
  • weysrtt Mar 13, 2011

    The electric treadmill brand is - Elite Fittness Equipment model No. T-1720

  • weysrtt Mar 13, 2011

    The info. plate attached to the treadmill reads Elite T-1720 N.14212
    Input 220-240 AC 50HZ
    Rated output 0.93 KW
    Rated Current 5 AMPS

    There are no other numbers or information on the machine

  • weysrtt Mar 13, 2011

    Yes, Australia.

  • weysrtt Mar 14, 2011

    Thank you for the information regarding the control board. As you pointed out it is causing the problem and I will contact a repairer in Australia.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,047 Answers

This problem is as a result of a bad control panel. The control panel controls all the functions of the unit it accepts commands and executes them. Often times it would accept a command but not execute as a result of malfunctions on the control board. This is why atimes it comes on and doesnt function. The control board is not totally bad but suffers from partial failure therefore the problems.
Best solution is to get the control board replaced this can be done by any service repair personnel or simply contact the nearest dealer for a repair person. Would have told you to try getting the boad fixed but that will only be a temporary solution as the problem will re surface in no time.
Hope this solution has been helpful?

Posted on Mar 14, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 271 Answers

I need the complete brand and model# to help you.

Posted on Mar 13, 2011

  • Android Man
    Android Man Mar 13, 2011

    there is a label at the frame usualy at front or side. I need the number from there to search for parts and tech info.

  • Android Man
    Android Man Mar 13, 2011

    your information is correct. but sadly I can not get any information on your equiptment here. looks like you live outside of the USA. wich is where I am. I tried all of my resources with no luck. sorry. perhaps someone else can help you here.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse is blown = need to replace, what type of fuse should I use


How to Change Treadmill Fuses ' LIVESTRONG.COM

www.livestrong.com > Sports and Fitness
Sep 29, 2015 - If the fuse on your treadmill has blown, it's time to replace it. ... Thetreadmill fuses are located inside the elevation motor. If you don't have the ...

Treadmill blowing fuse. ' All About Circuits

forum.allaboutcircuits.com > ... > Electronics > General Electronics Chat
Sep 1, 2014 - I have recently picked up a second hand treadmill with an issue (York Challenger ... If I unplug the motor from the control board it will not blow the fuse, and will give ... Not sure yet, but i'll replace the IGBT's/power mosfet (I still don't know whats ... Treadmill goes high speed then blows the fuse
Nov 25, 2015
Treadmill blows fuse as soon as it starts
Sep 29, 2015
treadmill motor controller problem?
Aug 25, 2012
Treadmill Controller - No power to motor
Feb 11, 2012
More results from forum.allaboutcircuits.com

Jan 20, 2016 | Exercise & Fitness

1 Answer

Where can I find parts for my vitamaster 2 treadmill


Go to this link, http://www.searspartsdirect.com/partsdirect/brands-products/Vitamaster-Parts/Treadmill-Parts

Jul 01, 2015 | Exercise & Fitness

1 Answer

My Sole F63 will slow down a few seconds after I start it then I get a low speed displayed on my control panel


please LUBE the deck belt+ rollers bearings too. You must do it evey 150 miles apros. This happen because the lack of maintenance schedule.
God bless you

Jan 21, 2013 | Sole Fitness Sole F63 Treadmill

1 Answer

My control panel on the Sole F80 Treadmill lights up but nothing I press works


adjust the REED SWITCH, see the diagram attached, clean it and tight the wires connector very well.
tight the ribbon cables insides from keypads +tight the wires connector from display board vs lower board and clean it.

God bless you
7_23_2012_2_19_45_pm.gif7_23_2012_2_20_23_pm.gif

Jul 22, 2012 | RTO Sole F80 Treadmill

1 Answer

Display functions on right side don't work as well as the fan


Hi drnelson3,

This problem is as a result of a bad control panel. The control panel controls all the functions of the unit it accepts commands and executes them. Often times it would accept a command but not execute as a result of malfunctions on the control board. This is why a times it comes on and doesn't function. The control board is not totally bad but suffers from partial failure therefore the problems.
Best solution is to get the control board replaced this can be done by any service repair personnel or simply contact the nearest dealer for a repair person.

Hope it helps.

Thank you for using FixYa.

Aug 29, 2011 | Epic 450 Mx Treadmill

1 Answer

Recently purchased the Crosswalk 570. Assembled


recently purchased a crosswalk 570 treadmill and used it and it worked fine but when we tried to use it today the machine made a strange noise under the hood. we noticed that the belt on the track was slightly rubbing against the hood. How can we fix it?

Jun 11, 2009 | Proform 575 Crosstrainer Treadmill

1 Answer

Dyer has power but doesn't start


dryer inside is very hot, 6 years long time, i have the feeling that wire was damaged and connected to each other cause this kind problem.

Jul 06, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kernmore elite He3t


Well there is one of two control boards that is malfunctioning, most common is the Machine (or Main) control board, there is also a display pc board in the control panel, but i have had few problems with that control. Unfortunately the main board is $300.

Sep 04, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

1,163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

914 Answers

Tom Chichester

Level 3 Expert

34170 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...