Question about MTX Car Audio & Video

1 Answer

I have a mtx audio thunder 4202 amp is it just meant to use for sub woofer or can it be used for front speakers as well ? is it 2 or 4 channel and what does that men?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,066 Answers

Yes, the amp can be used fof full range speakers. to use it a s such, the amp's "crossover" switch must be set to "off" (could also be labeled as "full-range" or "defeat").

the amp is 2 channel. 4 channel is for surround sound or to have independent front and rear channels/volumes. this 2 channel amp will support 4 speakers, but you wont be able to balance from front to back- the front and back speakers will be at the same volume all the time if both are hooked up to the amp.

Posted on Mar 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gauge wire ohm speaker


if the subs are different models or sizes don't install anything.
use the best subwoofer you have, if you use both you can have cancellation with uneven woofers or damage them. use a large ported box and tune it close to the music you listen to.
use a minimum of 4 gauge copper or cca wire. anything smaller and you risk burning the wire, the brand doesn't matter. use 14 gauge or larger for speaker wire and setup your impedance of your subwoofers in the pattern that will give you more power.
see here.
http://www.the12volt.com/caraudio/boxcalcs.asp

Nov 13, 2013 | MTX Thunder 4202 Car Audio Amplifier

1 Answer

Can you bridge 2 4 ohm kicker speakers to a mtx thunder 7801 amp?


Ya. Just hook one sub to your amp (bridged) and hook the other sub (positive and negative) to the first subs positive and negative

Nov 12, 2010 | MTX Thunder TA7801 Car Audio Amplifier

1 Answer

It keeps killing my battery


Power hungry unit and the battery may not be enough for the amp, could be a bad cell in the battery.....

Apr 06, 2010 | MTX Thunder 4202 Car Audio Amplifier

1 Answer

2 MTX Thunder Problem.. Bridging?


Is there a option on the chanels that say ''Bridged''? If so, you can hook the subs up in parellel or series to get different ohm loads. Usually the lower ohms, the more power amp puts out. Those subs can handle 225 watts RMS whitch means the power it can handle constantly. If the amp gives more than 225 watts RMs, you could be at risk of blowing the sub. If you could give me the model # of the amp, I can be of more help.

Feb 11, 2010 | MTX Thunder 4500 T4510-04 Car Subwoofer

1 Answer

Sub not working and red light on amp stays on?


the amp is under to much pressure get a bigger 1

Nov 18, 2009 | MTX Thunder 421D Car Audio Amplifier

1 Answer

I have 2 6x9 speakers up front 4 6 1/2 3-ways


Hello rjmiller4039,

Although amps with 5 channels are pretty rare, you can get one. Alpine, Boston Acoustics, Infinity, JL audio, MTX, and Polk all have 5-channels ranging in price from around $350 up to around $1,000. The Alpine PDX-5 will output 75X4 watts RMS for the front and rear stereo channels and 300 watts to the mono sub channel. It is priced at $599.99 at Crutchfield.

Hope this helps.


Sep 18, 2009 | Jl Audio 500/1 Car Audio Amplifier

2 Answers

Setting for...


HI DUDE .. U CAN ONLY SINGLE PC OF JL SUB BY BRIDGE MODE ... COZ UR MTX AMP HAVE 300WATTS RMS ....

Apr 05, 2009 | Alpine MRD-M301 Car Audio Amplifier

1 Answer

Wiring my subs to my amp


bridge it and rear channel if you need to know how to bridge let me know

Feb 07, 2008 | Phoenix Gold Octane-R 15.0:1 Car Audio...

2 Answers

Directed 1100d 2-channel amp


You will bridge the amp, and if the subs are all 8 ohm subs, you can probably wire them all in parallel, if they are all 4 ohm subs, you would wire then in series.

Oct 17, 2007 | Directed 1100d Car Audio Amplifier

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top MTX Car Audio & Video Experts

Professor_V
Professor_V

Level 2 Expert

92 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a MTX Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...