Question about Body Glove Dry Snorkel Purge Exhaust Valve Splashguard

1 Answer

Valve fell out - Body Glove Dry Snorkel Purge Exhaust Valve Splashguard

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Contributor
  • 277 Answers

If you still have the valve, you should be able to push it back in. If you don't, visit a scuba shop and they can order you a new valve.

Posted on Mar 12, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi i have a 2001 yamaha vt 600 f snowmobile backfiring alot what could it be and whats the worst ot could be?

Burned intake valve, out of time, excessive carbon on the valves.... check timing first then go inside the engine for burned valves.

Dec 05, 2014 | Yamaha Motorcycles

1 Answer

Looking for a float valve for montel living well pressure cooker, this products is no longer offered

Try contacting the manufacturer directly - their contact information should be in the user manual.

Jul 24, 2014 | Williams Montel Living Well 6 Quart...

1 Answer

I have a 1999 Damon Challenger Motorhome that blows cool air from heater .

Check the hoses to see if each hose is warm, usually 1 is warmer than the other, that enter the heater core from the engine.
If both are warm issue is inside vehicle, possible vacuum operated valve for venting or a cable, sometimes items drop down from dash, like toys, pencils, etc that could stop the action of the vents that adjust heat.
If 1 is cold then look for a valve possibly inside engine compartment on one of the heater hose runs, either vacuum line fell off, cable fell off or valve could be defective if no heat passes.
If no valve, then chances are the heater core itself is clogged and needs to be replaced.
This is all assuming that you have proper coolant level, the thermostat is functioning correctly, and your water pump is working, those should be verified as well when inspecting your heating issue.

Oct 29, 2013 | Rv Motorhome Dual Co & Lp Gas Alarm...

1 Answer

3 way valve

Put the spring in first ,then the valve and give it a 1/4 twist .

Oct 22, 2013 | Mr. Coffee Coffee Makers & Espresso...

1 Answer

Craftsman lawn tractor

Hi, had it been sitting some time unused?
Sounds like the valves are stuck in their seats and the rods bent when the motor pushed them with the cam.
You might be lucky and the one that fell in didn't get into the works.
Make sure you fish it out before doing anything else.
I'm guessing it is the typical side valve type motor?
Remove the valve cover (I guess you have already to get the push rod out) and using some sort of lever try and move the valves up against against their springs. Don't bend them with sideways pressure though. If they're stuck some CRC / WD40/oil or similar will help to get them moving. Remove the spark plug and spray CRC etc onto the valve heads inside the cylinder.
Assuming the push rod hasn't contacted anything moving while the motor was being wound over and done more damage, you should be good to go with new push / 2nd hand push rods. Just check there is some clearance between the push rod and the valve stem when each valve is closed.

Oct 09, 2013 | Craftsman Garden

1 Answer

No compression

check for a stuck valve then pull the head and see if the piston moves look to see if the valve seat fell out also look at the head gasket for a missing section

Jun 03, 2012 | Garden

1 Answer

Will not whistle

It is possible the reed valve broke.

Aug 02, 2009 | Electrolux CHANTAL Loop Tea Kettle -...

1 Answer

No heat

under the hood is aheater control valve fell both heater hoses make sure they are both warm if not this valve is your problem

Oct 24, 2008 | 1994 Ford Thunderbird

Not finding what you are looking for?
Body Glove Dry Snorkel Purge Exhaust Valve Splashguard Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Body Glove Scuba Diving & Snorkeling Experts

Bill Boyd

Level 3 Expert

44340 Answers

ray gallant

Level 3 Expert

45281 Answers

Are you a Body Glove Scuba Diving and Snorkeling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides