Question about Welding Tools

1 Answer

Trouble with contact in handle thrmo - Welding Tools

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,019 Answers

Sorry, but I think we need to know the make, model, and year of the plasma cutter, what sort of handle contact problem, etc.

Posted on Mar 12, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need a ARPI form

That would be some beurecratic stuf you need to contact the store about. This is a community for error handling, trouble shooting and the like. Most likely you can find the information, but most likely you need to find the correct thread instead of the one handling laptop hardware/software issues.

Feb 20, 2015 | Computers & Internet

1 Answer

How to replace thrmo fuse ?

can,t change normally,this task should only by a licenced specialist

Aug 25, 2014 | Maytag 30" Built-In Single Electric Wall...

1 Answer

Engine fan not working

Could be bad motor or you have a short in wiring and also could be the thrmo relay that cuts fan in and out.

Jan 24, 2012 | Dryers

1 Answer

My fan didn't work for a while , change every

It is not bad for the fan to run all the time.

May 12, 2011 | Garden

1 Answer

Hot water pilot light statrts but will not stay on. There is a new thrmo couple

Please confirm which model you have. Heading says DSI (electronic ignition) and it sounds like you are describing a manual light with thermocouple?

May 21, 2010 | RTO Atwood DSI-RV Water Heater-6 Gallon

1 Answer

Air conditioner want come on

ceck the thrmo remove it and by pass the wires hold them together if the ac starts then replace thermosat

Apr 29, 2009 | Heating & Cooling

1 Answer

My Whirlpool duet dryer is getting too hot


Mar 15, 2009 | Whirlpool LER5636P Electric Dryer

1 Answer

Dryer ducting.

Check all vent pipes and outside vent hood,thay should be keeped clean,and that the flex pipes are not kinked.Also a 4 " Y would be better than a T ,used to join them.Most dryers have a thrmo link,or a hi limit thermostat near the fan or in the outlet line.This is to prevent over heating. So poor venting,or bad lay out of the exust system may be the cause.If not the limit,or thrmo. be weak, and replacement is not that costly. Rob

Feb 28, 2008 | Maytag HYE3658AY Electric Dryer

Not finding what you are looking for?
Welding Tools Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Welding Tools Experts

Brad Brown

Level 3 Expert

15557 Answers


Level 3 Expert

75797 Answers

Bill Boyd

Level 3 Expert

42042 Answers

Are you a Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides