Question about Uniden Cordless Phone

2 Answers

Handset needs registration

I have a GE mod.no.25833ge3-a.I replaced the battery and it keeps kicking off from charging and the display says "handset needs registration" the dealer didn't know how to correct it.What can i do ?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

I had the same problem and have seemed to figure it out. Take the handset near the base. Press the Prog/Mute button at the bottom of the phone. It will display a message to press the Pager on the base. The phone will then ask you for a Handset Name. Press the Prog/Mute button again and it will name the handset Handset 1.. it is working

Posted on Feb 18, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I hav Apple i phone,only, internet problem

Posted on Jun 08, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DS6321 out of range, no power at base


This sounds like a registration problem, the handset(s)
and the base have lost identification with each other.

I. To address this, first de-register the handset(s) ---
do this procedure for each handset:

0. Start by taking off the battery compartment cover....

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??", press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY (why the cover was off)

9. Wait ~30 seconds, re-connect the battery & replace the cover

10. display reads "Not Registered" ===============================

II. To register the handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #1" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a few
hours and try the registration ( II ) again.

NOTE: the base can only handle 5 handsets and will
increment the number of each handset registered
until "Handset #5" has appeared, even if some of
the handsets are lost/not in use. Trying to register
more than 5 handsets will result in "Registration Failed."
===============================

III. To clear the base of all handset registrations and
be able to start registering again at Handset #1:

1. press [Find Handset] on the base and hold past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink.
2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration
3. for multiple handsets, return to II. above and
register each handset in turn.
===============================
Good luck !!

May 02, 2016 | Vtech Phones

1 Answer

3 of my 5 phones say "No Line"?


This sounds like a registration problem, the errant
handset(s) and the base have lost identification
with each other.

NOTE: the CS6429 works a maximum of 5
handsets, so you have a "fully populated system".

You will have to clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ).
=====================================
( I ). First de-register each handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( II.) To clear the base of all handset registrations

1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink. 2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration ===============================

( III.) To register each handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

===============================
Good luck !!

Apr 16, 2016 | Vtech Accessory Handset with Caller ID for...

1 Answer

Have a replacement handset, base is cs6729-2 handset is cs6729-3 how do i set up new handset to see base?


This sounds like a registration problem, the new
handset must be de-registered from its original
base and then registered to your base.

NOTE: the CS6729 handles a maximum of 5
handsets. If you have a handset displaying
"Handset #5" then you have a 'fully populated system'
even if you actually have only one or two handsets.

You will need to clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ) up to the maximum of five.
=====================================
( I ). First, to de-register a handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( II.) To clear the base of all handset registrations
( if needed, else skip ahead to ( III ). )

1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink. 2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration ===============================

( III.) To register each handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

===============================
Good luck !!

Oct 29, 2015 | Vtech Phones

1 Answer

Hand set says connecting even before it is reset with new base.


This sounds like a registration problem, each 'old'
handset must be de-registered from its original
base and then registered to the 'new' base.

NOTE: the CS6229 handles a maximum of 5
handsets. If you have a handset displaying
"Handset #5" then you have a 'fully populated system'
even if you actually have only one or two handsets.

You will need to clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ) up to the maximum of five.
=====================================
( I ). First, to de-register a handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( II.) To clear the base of all handset registrations
( if needed, else skip ahead to ( III ). )

1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink. 2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration ===============================

( III.) To register each handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

===============================
Good luck !!

Jul 23, 2015 | Vtech Phones

1 Answer

I have a vetch mod# CS6114 I checked the base unit and it gets power to charge phone but I can't get a dial tone. I even hooked up to another line and still won't work.


This sounds like a registration problem, the
handset must be de-registered from wherever
it thinks it is and then registered to your base.

=====================================
( I ). First, to de-register a cs6114 handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll from "Test Base" to "Test Handset", press [select]
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( III.) To register the cs6114 handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

NOTE 2: Some cs6114 bases do not have the "In Use"
lamp indicator. To register the handset simply park it
displaying "Not Registered" in the base cradle and wait
for the registration to occur. Pressing # as above may
be required, maybe not.
===============================
Good luck !!

Feb 12, 2015 | Vtech DECT 6.0 Cordless Phone with Digital...

1 Answer

Vtech cs6649 will not register more than one handset


The errant handsets must be de-registered from their
original base and then registered to your base.

NOTE: the CS6649 handles a maximum of only five
handsets. If you have a handset displaying
"Handset #5" then you have a 'fully populated system'
even if you actually have only one or two handsets.
In that case, you can clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ) up to the maximum of five.
=====================================
( I ). First, to de-register a handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( II.) To clear the base of all handset registrations
( if needed, else skip ahead to ( III ). )

1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink. 2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration ===============================

( III.) To register each handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

===============================
Good luck !!

Jan 09, 2015 | Vtech Phones

1 Answer

My phone displays out of range how to correct


This sounds like a registration problem. Try
de-registering the handset(s) and re-registering
to your base.

NOTE: the CS6429 handles a maximum of 5
handsets. If you have a handset displaying
"Handset #5" then you have a 'fully populated system'
even if you actually have only one or two handsets.

You will need to clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ) up to the maximum of five.
=====================================
( I ). First, to de-register a handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( II.) To clear the base of all handset registrations
( if needed, else skip ahead to ( III ). )

1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink. 2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration ===============================

( III.) To register each handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

===============================
Good luck !!

Oct 02, 2014 | Vtech Accessory Handset with Caller ID for...

1 Answer

Vtech cordless handset CS6209 will not connect with CS6229-2 base


Yes. The'old' handset must be de-registered from its
original base and then registered to your base.

NOTE: the CS6229 handles a maximum of 5
handsets. If you have a handset displaying
"Handset #5" then you have a 'fully populated system'
even if you actually have only one or two handsets.

You will need to clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ) up to the maximum of five.
=====================================
( I ). First, to de-register a handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( II.) To clear the base of all handset registrations
( if needed, else skip ahead to ( III ). )

1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink. 2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration ===============================

( III.) To register each handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

===============================
Good luck !! --

Jun 08, 2013 | Vtech Phones

2 Answers

Need help registering the GE additional cordless model 27911.


I had the same problem but I fixed it by:

1. Disconnect the battery on the handset.
2. Wait 1 minute and reconnect.
3. Register handset.

Jan 10, 2009 | Uniden Cordless Phone

8 Answers

GE Model 27911 DECT 6.0 Additional Cordless Handset not working


I had the same problem. What worked for me, after several unsuccessful registration attempts, was to disconnect the phone handset battery for about 1 min and then reconnect the battery. Run the handset registration procedure again. It registered for me on the first attempt after the battery reinstall. Good luck.

Jan 20, 2008 | GE 28111EE2 Cordless Phone

Not finding what you are looking for?
Uniden Cordless Phone Logo

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Phones Experts

kakima

Level 3 Expert

96396 Answers

Dave Ellis

Level 2 Expert

84 Answers

k24674

Level 3 Expert

7987 Answers

Are you an Uniden Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...