Question about Philips Magnavox REM-350 Remote Control

2 Answers

Hotel TV remote

I have a hotel tv with their channels programmed in. How can I re-program it to use my cable channels?

Posted by on

  • 3 more comments 
  • mchrist4 Jan 02, 2009

    I bought a used Phillips TV from a Thrift shoppe. It was obviously used in a hotel. How do I reprogram the channels for cable service?

  • awalk256 Jan 31, 2009

    I purchased one as well during a hotel renovation and it always goes to channel 14 when turned on. What's the fix.

  • Anonymous Feb 28, 2009

    I bought a hotel tv that does not receive all the cable channels.How do I reprogram it to get all the channels? The menu botton does not give me the option to program channels with the universal remote!

    Phillips model 27HT721OD/27

  • Eclark53 Apr 17, 2009

    Ii am in the same boat only I have Zenith TVs that I purchased from a liquidation of a major hotel chain. The cost of the TVs was very reasonable, but I cannot get into the menu function to change the settings there. I have Zenith H2505BT and H2530Y. Can anyone help me with securing a remote for these units.

    Thanks

  • Anonymous Mar 28, 2014

    I lost my remote and just had cable installed how can I perform channel search to program channels

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

For phillips tvs that come out of a hotel try this code with RCA universal remote. the big remote not a small remote. 319753 followed immediately by the mute button. this will pull up the tv setup menu.

Posted on Aug 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a phillips Hotel TV pre programmed to the stations they wanted. How can I reprogram it?

Posted on Oct 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a rca tv from a hotel closing down it didnt have the remote to it and I cant access all my channels how can I reprogram it with a universal remote


The universal remote will have several possible codes that can be used to work your TV. If the one you have programmed in is not doing the job reprogram another code. If only one code exists then you have a remote that is not fully compatible with your set. Some of the universal have this issue. Some of the RCA set required a dedicated and locked in remote. You would have to contact RCA and tell them your model number and serial number to get another remote. Beware these can get really expensive. I have included a site that you can use to find codes just in case you have lost that little paper that has the codes. http://www.rca.com/support/remote-control-support/

Apr 18, 2014 | RCA Televison & Video

1 Answer

Without remote control


You will have to take the remote for the DVD with you.

Dec 27, 2013 | Televison & Video

2 Answers

Brightstar BR100b Vizio


11_6_2013_4_52_58_pm.jpgWhat model of Vizio TV are you trying to program? The model number is usually on the back of the TV on a sticker.

Nov 06, 2013 | Brightstar UNIVERSAL TV REMOTE - FOR...

1 Answer

Brightstar br100z remote for a magnavox?


Brightstar (and similar) remotes are used in hotels and are uniquely coded so they don't depart along with a guest. Your only solution is to replace the remote

Nov 28, 2012 | Televison & Video

1 Answer

Hotel


It needs to be re-programmed to use your TV. Here is the manual link. Follow it to program the remote for you TV make.

http://audiovox2.info/docs/rca_acc/man/RCR350_DOC_OM.PDF

Jul 05, 2010 | RCA RCR350 Remote Control

1 Answer

I need the codes for a brightstar br100z remote for a symphonic t


Hold the set up button until the red light stays on on the remote. Press power until the TV responds. My sleep timer displayed after 23 presses (hotel room Magnavox TV). Stop pressing remote. The red light will then flash a few times once you stop. Problem fixed.

Feb 01, 2009 | Universal Remote Control Remote Control

4 Answers

32lc5dc lg tv stuck in hotel mode


it is quite possible, if you bought this set from a hotel liquidation, it might still have it's lodgenet card. If it does, then it may be stuck on the channels the hotel had lined up. If there is a lodgenet card (where the cable jack is on the back) you can remove the 2 screws and just pull the card out an inch (leaving it attached to the black cable). Once that card is out, the tv should fall back to normal use. You might need to do a facotry reset to unlock TV options at that point. Only way around this would be to remove the 2 screws holding in the lodgenet card, and pulling it out of the back of the set (Don't have to pull it out all the way, just enough to disengage the data socket. Once the card is removed, you would need an actual LG remote (not the pay per view remote) and hit menu a bunch of times until it stops flashing menu on and off. Once it stops, you type in on the keypad, "98765" "ENTER". This will take you to an installer menu. Scrolling down to the highest numer there is (Should be one backwards from the "000" you start on" there is "Factory Reset" and you use the right arrow key and set it to "1" and then press enter. The TV will flicker a couple times, and then, all inputs are active.

Jan 17, 2009 | Philips RC2573 Remote Control

2 Answers

Stuck in hotel mode 32 lg lcd


hold down MENU button for approx 5 seconds, then enter 1105 this will bring up the hidden menu then turn off the hotel mode.

Hope this Helps
Cheers

Little Dish Fitter

Jan 16, 2009 | Philips RC2573 Remote Control

6 Answers

Zenith TV not programmed for home purpose


If you have a remote that can access menu and your remote has number buttons and an enter key, you can follow this instructions to go to installer menu. Note that the installer menu is slightly different for each model, eg. some options are not available.

I was able to go to installer menu using two universal remotes. The remotes that I used were Dish Network 3.0IR and RCA RCU300WBL. Both remotes programmed for Zenith H2531DT TV. The reason why I had to use two remotes is that Dish Network remote was only able to access menu. It did not have ENTER key but RCA remote had ENTER key but I wasn't able to go to menu with that.

To go to installer menu (different from regular menu):

- Hold MENU for 8 seconds.
- Press 9, 8, 7, 6 and ENTER in the sequence.
You should be in the installer menu now. There should be a line that looks something like this:
03 VERT POS 13

Use SELECT button to scroll through each option, and ADJ button to adjust the values for each option. For example, to enable the front panel buttons on your tv, set KEY DEFEAT to 0. Other options that you might want to check:

CHAN LOCK which locks your TV to a single channel and wont let you change (set 0 to turn off)
START CH/VOL will set your tv to a specified channel when you turn on tv. (set 255 to disable)


You will have to look in the menu for some of the options because they are different for different TV series. A good place to find manual is on www.zenith.com or http://safemanuals.com/

I work in an old hotel and it took me few hours to figure out how to disable start channel lock. It drove me nuts. I hope someone finds this useful.

May 26, 2008 | Zenith SC652 Remote Control

2 Answers

ZN110 remote


Magnavox codes 002,009,109,118,309,402,408,502,508,510,807, 917

May 11, 2008 | Zenith ZN110 Remote Control

Not finding what you are looking for?
Philips Magnavox REM-350 Remote Control Logo

2,616 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69808 Answers

matt martin
matt martin

Level 3 Expert

1198 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...