Question about Zonet ZSR0104CP (zsr0104cp) Router

1 Answer

No communication from the router

I have try to address the router but do not get response back from the router, Try call Zonetusa but up till now I have recieved no response from them. My email address is h_bat@yahoo.com. Thanks.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 144 Answers

Hello!

-- what is the operating system of your computer?
-- is this working fine before or is this a brand new router

you may try this and see if this help solve your problem. make sure your computer is directly connected to the router

Step 1: Shutdown the computer.
Step 2: reset the router while power on then Unplug the router’s power cable.
Step 3: Unplug the Broadband modem’s power cable and wait for 30 seconds.
Step 4: Plug in the Broadband modem’s power cable and wait for its lights to appear stable.
Step 5: Plug in the router's power cable once the modem’s lights appear stable.
Step 6: Power on the computer on and configure the router settings
Step 7: test the Internet connection.

if this still didnot work, upgrade the firmware of your router and repeat the same steps.

note:

configuring the router settings will depends who is your provider. if your isp is dsl you need to configure your ISP username (email address format) and password on the router. if your router is a cable no need to change any settings on the router. it should automatically work

if you are still having trouble configuring your device, try to call supportrix

Posted on Aug 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set up my router Linksys Wireless-G 2.4ghz 54mbps? I received the router from my dad and it just has the cables and no cd or manual. When I try to set it up, it prompts that it does not recognize...




Reset your router back to the default factory settings.

This is done by simply holding down the reset button located on the back of the unit for at least 30 seconds. Once the router has been reset, it must be reconfigured. Using your web browser go to URL address http://192.168.1.1. You will then be prompted to login to your router. A log-in screen asking for the password will automatically appear. At this time enter the default password "admin", in lower case letters into the password field. The username field may be left blank at this time. (Note: both the default username and default password are set to "admin" on some of the newer Linksys router models).

To get online:
You do not have to use the cd.
Shutdown your PC. Unplug the power from the router and the cable modem.
Wait 30 sec. then plug in the power to the cable modem, wait 30 sec. then plug the power to the router. Wait till you have "Internet" light then restart your PC. The PC should pick up an IP address and you should be able to get on-line. This is if you have a cable service provider. If you have DSL, the router needs to be configured with PPOe.


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe





Feb 07, 2011 | Linksys Wireless-G Broadband Router

1 Answer

I type 192.168.1.1 but it fails to access my router. It comes back and says webpage not found.


Hi,

This issue could be because of the following reasons:

1. Physical connectivity issues.
2. Router set up with another address.
3. Browser issue.

To isolate and fix this you need to ensure that we have connectivity.
Make sure you are using a kown good LAN cable and there are lights on the computer as well as the router.

You are trying the correct address which is the default for Linksys routers, you might want to try http://192.168.0.1 as well.

Please try to use another browser to access it.

In case this fails please press the reset button on the back of the router and hold it till the lights on the front blink to indicate that the router has been reset.

Once reset please try with the default IP address again.

If you require any further assistance, please comment and let me know, and I will be happy to assist you to further resolve your issue.

I will appreciate your feedback and positive rating for this solution.
Thank you.

Jan 22, 2011 | Linksys Wireless-G Broadband Router

2 Answers

My router will not connect the power light keeps blinking


Check this tip out from Linksys. It is for a G VPN Router but you could use the same steps to troubleshoot. Title: Resolving Blinking Power or Diag LED on a Linksys Wireless-G VPN Router Article ID: 4982 If the Power LED on your Linksys router is blinking, this means the device is not ready. It should go off once the router completes its diagnostic test. If the Power LED won?t go off, it indicates that there?s a possible hardware problem with the router. To resolve this, you will need to perform five steps: Resetting the Router Assigning Static IP to the Computer Pinging the Router Accessing the Router?s Web-based Setup Page Updating the Router?s Firmware For instructions on how to reset the router, follow the steps below. Resetting the Router Hold in the RESET button at the back of the router for 30 seconds. Unplug the power to the router then plug it back in. If after resetting the router and the Power LED is still blinking, try resetting the router again for another 30 seconds. Then proceed with assigning a static IP address on the PC. For instructions, follow the steps below. Assigning a Static IP Address on Your Computer Most of the time, if the power LED on the router is blinking it loses its ability to assign IP addresses to the PCs connected to it, which is why you need to assign the computer a static IP address. After assigning a static IP address on the computer, check if the computer is still communicating to the router by performing a ping test. To ping the router, follow the steps below. Pinging the Router Ping test helps trace the communication between the computer and the router. The computer sends packets to the router and in return the router sends out replies to validate the connection. In this example, our router IP address is 192.168.1.1. NOTE: If you?re using Windows 98 or ME, click here. Windows 2000/XP Step 1: Click Start, then Run. Step 2: When the Run window opens, type ?cmd? in the Open field, then click OK. Step 3: When the MS DOS Prompt appears, type ?ping 192.168.1.1? and press [Enter]. Step 4: Check the ping statistics. You should get Packets: Sent =4, Received =4, Lost = 0 (0% loss). NOTE: If you?re not getting good replies from the router, it means the router is not communicating properly with the computer anymore. You can already consider the device defective. Windows 98/ME Step 1: Click Start, then Run. A window similar to Step 2 will appear. Step 2: When the Run window appears, type ?command? in the Open field, then click OK. Step 3: When the MS DOS Prompt appears, type ?ping 192.168.1.1? and press [Enter]. Step 4: Check the ping statistics. You should get Packets: Sent =4, Received =4, Lost = 0 (0% loss). NOTE: If you?re not getting good replies from the router, it means the router is not communicating properly with the computer anymore. You can already consider the device defective. If you get good responses from the router, access the router?s web-based setup page to see if a firmware update is possible. For instructions, follow the steps below. Accessing the Router?s Web-based Setup Page In order to perform a firmware update, you should be able to access the router?s web-based setup page. Updating the firmware is one way of resolving the blinking power light on the Linksys router. To access the router?s web-based setup page, click here. NOTE: If you?re having difficulties accessing the router?s web-based setup page, the router is considered defective. If you?re able to access the router?s web-based setup page, proceed in updating the firmware upgrade.

Jul 21, 2010 | Linksys Wireless-G Broadband Router

1 Answer

No connection to internet


You need to do a reset to the router hold in the the rest buttons for 30 seconds.Then shut down the pc and try it again.

When it boots up see if there are any errors.
I also want you to go (command prompt) type cmd in the run box and type in just like this
ipconfig /all
see if an ip address comes up
then type in ipconfig /release
wait then type this
ipconfig /renew

Wait till it collects info then restart computer it should resolve after that its a communication error with the router and the pc.

Mar 02, 2010 | Zoom (56600000) Router

1 Answer

My DI-524 has suddenly lost all settings and can no longer recognise my IP address etc. When I try and connect I get the message "insecure site", or, enter KEY code to connect. Can anyone help me, please?


am not sure if the communication is from the router. Can you check if you have any firewall enabled. If yes, try to disable the firewall and try again.
if it still doesnt work, try to reset the router and bring it back to factory defaults.
Thanks Ranjit

Dec 07, 2009 | D-Link AirPlus DI-524 Wireless Router

1 Answer

The router does not detect the working Internet connection


check the dns value ip address of the isp and change the ip address of the router is default is 192.168.1.1 change in different series then check the friewall disable it any proxy server change it then check you get it and reconfigure it

Mar 12, 2009 | Computers & Internet

1 Answer

Cannot access url address


try connecting with cable and check if ur re able to go online if u re getting the message as limited or no connectivity in the wireless area network , wireless is not configured properly or wireless key entered is incorrect try opening the gui page of router try if ur able go online with the safe mode (restart ur computer press F8 till u get black window with the message as safe mode with networking) choose ur logon and check if ur are able to go online, if working its antivirus and firewall issue check the setting in the browser for internet explorer (go to tools internet options , connection and select to never dial a connection , they check in lan if no boxes are ticked) Try resetting the internet explorer or the brower u use

Sep 07, 2008 | D-Link RangeBooster G WBR-2310 Wireless...

2 Answers

When i try and set up my wireless router it tells me the router is not detected


Please ensure that you have the router connected via the blue cable directly to your computer's ethernet port. You should be able to interface into your router's config page by typing in 192.168.1.1 in the web browser expolorer bar. Hope this helps, however, please do get back to me should there be anything else. Thanks.

-Technomancer

Jun 02, 2008 | Linksys Wireless-G WRT54G Router

2 Answers

I purchased a wireless router model wrt110 early this month, installed and working fine unitl last night had to uninstall and tried to install it back i get to the installation to figure the router and i...


NO need to worry i will provide a valid trouble shooting steps
I think u have used the set up cd..dont use the Cd..i will give u the exact steps..

U dint specify that whether u r using the cable Internet or DSL!!



1,connect the blue cable between the computer and the router(any 1 of the 4 ports in the router)

2,connect the other Ethernet cable between the Modem(came from ur internet people) and the Router's Internet port(standalone port at the back of the router)

3,In the rear panel of the router u can see the reset button.with the help of the paper or ball point pen,press it hardly and hold it for 1 minute..

4,Now turn off ur modem and the router..wait for other 1 minute..

5,turn onn only the modem and wait till all the lights lit.now turn on the router and wait till the power light is solid..open the internet Explorer it should work..


STeps for DSL Connection(verizon)

1,connect the blue cable between the computer and the router(any 1 of the 4 ports in the router)

2,connect the other Ethernet cable between the Modem(came from ur internet people) and the Router's Internet port(standalone port at the back of the router)

3,In the rear panel of the router u can see the reset button.with the help of the paper or ball point pen,press it hardly and hold it for 1 minute..

4,Now turn off ur modem and the router..wait for other 1 minute..

5,turn onn only the modem and wait till all the lights lit.now turn on the router and wait till the power light is solid..

6,open internet Explorer and in the address bar..enter as 192.168.1.1..it will prompt for a user name and password..leave the user name blank and the password will be admin.

7,linksys set up page will open..there u can see local ip address which says 192.168.1.1.
please change it as 192.168.2.1..click on save settings at the bottom of the page..
it will say like "settings are successful please release and renew the ip address".click continue or OK

8,Now turn off ur modem and the router..wait for other 1 minute..turn onn only the modem and wait till all the lights lit.now turn on the router and wait till the power light is solid.

9, Open Internet Explorer and it shuld Work....

TRY IT AND GIve me ur feedback

May 31, 2008 | Linksys Wireless-G WRT54G Router

1 Answer

Hard Wired Port Problem


please dont assign any manual addresses in ur computer..let it be automatic...

u said that u connected the computer to Ethernet ports in the router...
check whether the light are lit in the router corresponding to that particular port..
check the ip address to that particular computer(hard wired to the router)
ip address should be 192.168.1.100 or 101 or 102..if the ip addres comes in this range means its working good...
if ther is no ip means please follow this steps...

1,connect the blue cable between the computer and the router(any 1 of the 4 ports in the

router)

2,connect the other Ethernet cable between the Modem(came from ur internet people) and the

Router's Internet port(standalone port at the back of the router)

3,In the rear panel of the router u can see the reset button.with the help of the paper or

ball point pen,press it hardly and hold it for 1 minute..

4,Now turn off ur modem and the router..wait for other 1 minute..

5,turn onn only the modem first and wait till all the lights lit.now turn on the router and wait

till the power light is solid..open the internet Explorer it should work..






May 31, 2008 | Linksys Wireless-G WRT54GS Router...

Not finding what you are looking for?
Zonet ZSR0104CP (zsr0104cp) Router Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zonet Computers & Internet Experts

Barbat Nae
Barbat Nae

Level 3 Expert

508 Answers

Prashant M
Prashant M

Level 3 Expert

2259 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Are you a Zonet Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...