Question about Schlage BE365-CAM BE365CAM619 Satin Nickel Electronic Security Keypad Elect

1 Answer

I have spent over an hour looking for information on how to set a code for my Schlage BE365 CAM 619 keyless access deadbolt. I want a very SIMPLE explanation. Don't tell me to go to the Schlage web sites. I have already tried. HELP!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 155 Answers

First make sure you have a fresh new battery installed
Next if you feel you have fiddled with it so much you can reset the lock to the factory default settings, to do this

1.Disconnect the Battery

2. Press and hold the Schlage Button while reconnecting the battery

However proceed before resulting to a reset and see if you are sucessful.

There are preprogrammed user codes already programmed into the unit
These two USER CODES (UC) are on the Yellow Sticker and on the Installation documents that came with the lock. Also the 6 Digit PROGRAMMING CODE (PC) is listed in the same location.

Assuming the lock was installed correctly and tested for correct operation.. proceed...

First.. I agree with you about the instructions.. many places they use the word "press" when they should have used the word "enter".. or phrase.. "enter the user code by pressing the corrosponding numbers".. however..

With the door open test the lock function
Press the Schlage button.. this should extend the bolt

Next Enter one of the two supplied preprogrammed user code (a) or (b) and rotate the thumbturn away from the door edge (generally to your left or counter clockwise) This should retract the bolt.

To Enter a New USER CODE (UC)

1.Enter the 6 Digit Programming Code (PC) via the key pad

2.The Schlage button will glow Orange

3.Press and release 1 on the keypad

4.Enter your new/desired 4 Digit USER CODE (UC) via the keypad

5.Enter the new/desired 4 Digit USER CODE (UC) via the keypad again (yes a second time)

The Schlage button should flash green.. signalling the program was sucessful

Repeat the lock function test using the new User Code (UC)
Make sure you write the new UC number down.

This lock will store up to 19 UC codes.

Good Luck!

Posted on Mar 11, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change baterry o schlage be365


To change the battery on the BE365, you need to remove the inside cover by removing the two screws (one above and one below the deadbolt knob). Be careful to tuck the wires inside the lock so that they will not be crimped when you put the cover back on.

Do you here a beep and see a flashing light? Usually if pressing the Schlage button unlocks the deadbolt, your installation was done improperly. The cam on the base plate must be vertical and the bolt must be correctly installed.

You will always be able to lock and unlock the deadbolt with the inside thumb knob.

I hope this helps.

Cindy Wells

Dec 04, 2013 | Schlage BE365-CAM BE365CAM613 Oil Rubbed...

1 Answer

Shlage keypad dead bolt unlocks when you press the


Does my Schlage BE365-CAM BE365CAM505 have a feature that allows it to automatically lock the deadbolt without having to enter code and turn the dial?
Sort of. The lock has what is called the "turnlock" feature. When enabled, you have to only push the Schlage button, then manually turn the dial. When disabled, you have to enter the user code, then turn the dial.

To enable/disable this feature, enter your Programming Code--press the Schlage button--Press 7.

Each time you do this, you toggle between enabled and disabled.

Videos for installing and programming can be found on this page:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Scroll down and find them under the heading Electronic Security--Keypad deadbolt 365

Aug 31, 2012 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

Door will unlock without entering code


"Does my Schlage BE365-CAM BE365CAM505 have a feature that allows it to automatically lock the deadbolt without having to enter code and turn the dial? "
Sort of. The lock has what is called the "turnlock" feature. When enabled, you have to only push the Schlage button, then manually turn the dial. When disabled, you have to enter the user code, then turn the dial.

To enable/disable this feature, enter your Programming Code--press the Schlage button--Press 7.

Each time you do this, you toggle between enabled and disabled.

Feb 15, 2012 | Schlage BE365-PLY BE365PLY626 Satin...

1 Answer

Does my Schlage BE365-CAM BE365CAM505 have a feature that allows it to automatically lock the deadbolt without having to enter code and turn the dial?


Sort of. The lock has what is called the "turnlock" feature. When enabled, you have to only push the Schlage button, then manually turn the "dial". When disabled, you have to enter the user code, then turn the dial. So either way, you still have to turn the dial.

To enable/disable this feature, enter your Programming Code --press Schlage button--press 7

Each time you do this, you toggle between enabled and disabled.

"How can I program my electronic keypad lock when the instructions with the Programming Code have been lost?"
The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

Complete installation & programming instructions can be found here:

http://consumer.schlage.com/Project%20Documents/P515-858.pdf

Notice that the above is a .pdf filetype. That means that you need to have Adobe Reader or similar installed on your computer to view it. So if you are unable to view the file, download (for free) and install Adobe Reader first. You can get it here:

http://get.adobe.com/reader/

Videos for installing and programming can be found on this page:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Scroll down and find them under the heading Electronic Security-Keypad Deadbolt BE365

Good luck!

Aug 11, 2011 | Schlage BE365-CAM BE365CAM505 Lifetime...

1 Answer

How to change the code


You should find the links to the information you need on this page:

http://consumer.schlage.com/Products/Pages/ProductDetails.aspx?ModelNumber=BE365%20CAM%20619

Feb 17, 2011 | Schlage Camelot Deadbolt Keypad, Satin...

1 Answer

.how to reset code push


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

There's a video that shows you how.

Good luck!

Nov 20, 2010 | Schlage BE365-CAM BE365CAM505 Lifetime...

1 Answer

I have a BE365 Lock on my door. When I go to lock the door it wants the code punched in and the knob turned. When i unlock it, it just wants the schlage button pushed and knob turned. HELP


How do I enable the alternative setting (Code Turn)? (BE365 Deadbolt only)
1.) Enter your current 6-digit programming code
2.) Push the button
3.) Press 7 on your keypad

Nov 16, 2010 | Schlage BE365-PLY BE365PLY626 Satin...

1 Answer

How to change the battery on my BE365-CAM-716 Schlage Keypad Deadbolt


Problem fixed by having my wife look it up on the Schlage website. The deadbolt has a flash memory so your combinations and codes will not be lost when the batteries are changed.

Sep 21, 2008 | Schlage BE365-CAM BE365CAM613 Oil Rubbed...

Not finding what you are looking for?
Schlage BE365-CAM  BE365CAM619 Satin Nickel Electronic Security Keypad Elect Logo

477 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schlage Locks & Locksmithing Experts

JOHN LAPIER

Level 3 Expert

2428 Answers

ken skalski

Level 2 Expert

152 Answers

Cindy Wells

Level 3 Expert

5185 Answers

Are you a Schlage Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...