Question about Fisher and Paykel Kitchen Ranges

1 Answer

Is it alrignt to put an aluminium oven tray on the bottom of the titan double triduim oven? Will it damage the element?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 68 Answers

You do not want to set anything on the element. Setting anything on the element, and turning it on will burn up the element, as well as it will probably melt the aluminum tray if it is on the element.

Please rate this solution

Posted on Jul 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Will just replacing the oven element fix my Kenmore model 911.955879range oven? It sparked, broke in two and a white flame continued going around the element, wouldn't stop I had to shut breaker off.


Hello Jennifer;

My name is peter. I am a retired field service appliance technician.

Good for you - turning off the breaker.

You have a older oven. Usually there is a spark or crack in the oven element. In your case the element was so embrittled it broke into 2 pieces.

Before you use the top range burners to be on the safe side you need to disconnect the oven element. You may have damaged the oven control board to where it is locked into power for the oven.

25713262-01ium3bsyoj5ql4fhv4kpwvp-4-0.jpg 1.) Remove the bottom drawer to reduce weight.
2.) Put a rug on the floor in front of the oven, so when you pull the oven out it does not scratch the floor.
3.) Pull the oven out so you can get behind it.
4.) Unplug the unit.
5.) Remove the back bottom cover.
6.) Disconnect the heating element and remove from oven.
7.) Rap the two loose element connections in the back with electrical tape.
8.) Follow the element loose connection to the control board at the top. Disconnect at the oven control board.
9.) Inspect the loose wiring from the control board to the heating element for burns or melting.
10.) Plug the oven back in and turn on the range burners.

The part number for the oven element is WB44T10014. Sears wants about $95.00 for this part. Search the internet for this part number and get it for about $28.00.

Your oven control board may have become damaged. Recently I replace one for a friend. Sears wanted $256.00. I got a remanufactured board over the internet for $30.00.

Get back to me and let me know what is going on.

May 25, 2015 | Kitchen Ranges

2 Answers

Melted aluminum foil on inside of stove bottom how do we get it off?


Cynthia,
I would suggest using something wooden so that you do not damage the surface of the oven. You could try a wooden dowel that you cut at an angle so that you have a point. Also, most manufacturers do not recommend putting aluminum foil under the elements or on any of the racks. One of the things that can happen is what has happened to you and it also can cause premature failure of the heating element if you put it under the heating element. The same goes with putting foil in the drip pans, not a good idea. Hope this helps!

Apr 04, 2015 | Kenmore Kitchen Ranges

1 Answer

Single element stove oven, doesn't get hot enough


Your oven probably has a feature called a hidden bake element. The element is located beneath the floor of the oven. (Because of this, NEVER put aluminum foil on the bottom of the oven because it will get hot enough to melt the aluminum foil and make it bond to the bottom of your oven.) You can adjust the temperature of your oven through the electronic oven controls. Check your owner's manual for how to do this.

Oct 08, 2014 | Kenmore Kitchen Ranges

1 Answer

Grill is not working


Hello,
Is The small amount of heat you are getting coming from the bottom element in the top oven or is half the top Grill element working.To start with you have a double grill element and either the whole element has gone or just half the element.This is controlled by a selector switch which could be at fault or the Thermostat that controls the temperature.

Hope this helps.

Jul 07, 2010 | Electrolux Insight EKC6049X Stainless...

1 Answer

The bottom oven element does not ignite. the broiler is ok . a fire was put out with an extinguisher. no noticable damage to the element... what else can i check/ clean?


Unless you had a big spill in your oven, a "fire" in the oven is almost always a result of a burnt out element. Look very closely at the element for a rough spot. Look in the area where you noticed the fire. (that would be where the magnesium inside the element burned) The only easy way to confirm the element is good or bad would be to ohm check it with the power off and at least one wire disconnected from the element. Other than the mess, the fire extinguisher would not cause any damage to the oven.

Oct 16, 2009 | GE Profile Spectra JBP95 Electric Kitchen...

1 Answer

FEF366DC Electric Kitchen Range Problem


osunds as if yo perhaps blown the circuit breaker, got to the fuse box and try resettting the breaker first , if not labeled its going to be a "double breaker" youll need to fully turn it off and then reset to on position

Jan 25, 2009 | Frigidaire FEF366DC Electric Kitchen Range

2 Answers

Oven problem


if you had a power surge then the resistors on the board cannot handle it. i am no electronics expert however i am a range expert and usually it happens when 1 you live in a very rural area and have frequent power surges.. 2 get struck by lightning.. 3 may have a miswired outlet.

Jan 20, 2009 | GE Profile 30" Free-Standing 5 Burner Self...

1 Answer

Is it alright to put an aluminium oven tray on the bottom of the titan double triduim ovens?


You do not want to set anything on the element. Setting anything on the element, and turning it on will burn up the element, as well as it will probably melt the aluminum tray if it is on the element.

Please rate this solution

Jul 31, 2008 | Fisher and Paykel Kitchen Ranges

1 Answer

Oven bottom wont heat


can you seee the lower bake element? usualy when bad it will be apparent with a visual inspection of the element.if there is damage to the element order a replacement . 2 screws and 2 wires . no problemTURN OFF POWER ITS A LIVE ELEMENT AT ALL TIMES!!!!!!!

Mar 16, 2008 | Frigidaire FEF336BC Electric Kitchen Range

2 Answers

Oven not heating up


can you see the bottom element?? if so usually , its obvious when the element goes bad, youll see the damage.TURN OFF POWER. 2 screws remove elemnet from the front 2 wires, plug in aa new one and your good

Feb 29, 2008 | Frigidaire FEF336BC Electric Kitchen Range

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Kitchen Ranges Experts

linnap

Level 2 Expert

76 Answers

Bob Kirkwood

Level 2 Expert

75 Answers

Claude Kayser
Claude Kayser

Level 3 Expert

9098 Answers

Are you a Fisher and Paykel Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...