Question about Canon PowerShot SD100 / IXUS II Digital Camera

1 Answer

Black lcd The lcd suddenly went black. It will take photos, but they are black. It's eye is dead.

Posted by on

  • silani Jul 31, 2008

    You Rock! Thanks!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Go to this website and read the advisory. This is a known issue...

http://www.usa.canon.com/consumer/controller?act=PgComSmModDisplayAct&fcategoryid=223&modelid=9825&keycode=2112&id=48264

There are instructions on getting this repaired free of charge.

Posted on Nov 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lights for 480v photo cell control, the blue one, come on and stay on, any suggestions, or reasons this would happen? Is longer than 5 minutes


Unknown if this is new installation, or old installation that went bad.
Old install, then check voltage is correct for rating plate, check that line power is not under-voltage, check that photo control receives enough light by shining 120Volt light bulb onto photo eye, replace photo eye
New install, check wiring. Photo cell has 3 wires, For example Black White and Red.
Black and White connect to power source, and Red goes to load.
http://waterheatertimer.org/How-to-install-and-troubleshoot-photo-eye.html

May 01, 2012 | Hardware & Accessories

1 Answer

I have a 18 month old inspiron 1545 and suddenly its display went to dead black. But still windows is loading up i can hear sounds and music but can't see a single blink on the display. Don't know...


Hi paramvirgull...

Hook your laptop to an external monitor and see if the screen comes on...if it does then your lcd screen is faulty and needs replacment.
If it does not come on then re-download your video driver/s. If that does not work.
Maybe your lcd inverter or backlight bulb is faulty and needs replacement.
Please take time to rate me thumbs up

Sep 16, 2011 | Dell Inspiron 1545 Notebook

2 Answers

My timer comes on at dusk and the lights blink on and off until they shut off 6 hours later.


1) Put black tape over photoelectric eye on timer.
Photo-eye is small round eyeball that bulges out.
See of lights stay on.

2) Turn timer away from source of light so photoelectric eye does not pick up feedback from lights.

It sounds like photo eye is receiving enough light that it turns off, 'thinking' it's dawn.
And then when lights are off, photo eye 'thinks' it's dark again, so lights come back on.

Let me know if this is the answer, because it's Christmas season, and folks have been asking about blinking outdoor timers. And then you're en-route to become fixya expert and boost your GNP by 3 cents an answer.

Nov 30, 2010 | Woods Outdoor Photoelectric 24 Hour...

1 Answer

Hi, my olympus FE-290 suddenly went black. couldnt see through the lense. Couldnt click the snaps. It happened all of a sudden. It did let me click the photos 5 mins before and suddenly when I was trying...


I just solved the problem. The lens system wire connector to the main pcb was out of this female conector. Only you need its disassemble the camera and in the back of the lcd there's the conector, press it with carefully and test your camera.

BE CAREFULLY WITH THE LCD WIRE WHEN YOU TURN IT.
08d4974.jpgf05216b.jpg2b4ee45.jpg165f896.jpg

Feb 07, 2010 | Olympus FE-290 Digital Camera

1 Answer

My samsung suddenly went black last night and now there is sound when I switch it on, but the screen is black. Is this a common fault and what is the likely cost of resolving this?


hi there
this is a comon proble with lcds
this might be that the lcd is dead or faulty or the signal cable that runs to the lcd is faulty or the lcd its self is faulty
So it would be cheaper for you to buy a whole new unit as parts are expensive

Oct 23, 2009 | Televison & Video

1 Answer

Maytag Microwave Model#MMV4205BAB


My LCD read is dead. can not read any numbers.

Nov 06, 2008 | Microwave Ovens

1 Answer

Power


check the power pack to see if it has the required output voltage, usually 12-15 volts. solidstate power packs are prone to failure. The LCD screens require between 2 and 4 amps to power them. A strain on some power packs. Gary(Honkity Hank)

Sep 18, 2007 | AOC LM929 (Black) 19" LCD Monitor

Not finding what you are looking for?
Canon PowerShot SD100 / IXUS II Digital Camera Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Cameras Experts

kakima

Level 3 Expert

102366 Answers

TC CAMERA REPAIR.Com...

Level 2 Expert

168 Answers

old marine
old marine

Level 3 Expert

1869 Answers

Are you a Canon Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...