Question about Projection Televisions

1 Answer

Tv will not turn on standby button keeps flashing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 167 Answers

Hello. well it sound;s like you have a power supply problem.!!! your not getting the voltage from the power supply that you need to start it up.hope this help's let me know. "good luck"

Posted on Jul 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TV turns itself off, then on automaticlly


The fan should run for a few minutes after shut off to cool the lamp down.

If I read and understand correctly somewhere in the cycle you are getting 5 red blinks? that is an error code........

Either you or I can Google the model number of the set with 5 blinks.....or visit the Sony site to see what it means.....

Apr 24, 2012 | Sony KF-42WE620

1 Answer

The stand by light keeps blinking, this has happened before but then the TV came on. What to do as it has been blinking for a long time now.


The self-diagnostic function of the projection TV will cause the STANDBY light to blink or flash when the television detects an issue. The number of times the STANDBY light flashes corresponds to a specific issue. As per the two examples below, some of the issues may be resolved without the need for service.
  • If the STANDBY light flashes three times in sequence, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue.
  • If the STANDBY light flashes four times in sequence, the TV may be overheating. To resolve this issue, ensure that the back of the TV is well ventilated.
If the flash sequence is not listed above or the light continues to flash, follow the steps below to perform a power reset:
  1. Turn off the television. IMPORTANT: For a projection TV that uses an internal lamp, wait 5 minutes after turning off the TV to allow the lamp to cool before continuing with the following steps.
  2. Unplug the TV power cord from the electrical outlet.
  3. Let the TV remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the TV is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the TV.
  5. Turn on the television. NOTE: If the TV does not turn on immediately, the fan may need to finish its cycle. This is part of the cooling process for some projection TVs and is normal operation. After the fan turns off, attempt to turn the TV on again.
If the issue is still unresolved after following all of the troubleshooting steps,service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.

Nov 15, 2010 | Sony Projection Televisions

3 Answers

Four blinking lights from standby led lamp after I turned on the TV.


Yeah, it is not lamp problem. Check fans in tv as one of fan is stopped for some reason and causing problem.

Jun 29, 2010 | Sony KDS-R50XBR1 50" HDTV

1 Answer

My sony projection tv model kp-53hs30power button keeps flashing and wont turn on! Why is it doing this?


The standby/power switch should be flashing in a repeatec count. Please post that count. It is an internal diagnostic that will tell us the problem with the set and thus the actions required to repair it.

Thanks,
Dan

Jan 01, 2010 | Sony KP-53HS30 53" Rear Projection...

1 Answer

It keeps flashing between flashing lights regards


Hi.

The TV stays in standby because protection circuit kicked in.

Protection kicks in when an internal fault had been detected.

In your case the SCART cable may have caused a short.

When on protection the TV will stay in standby, will not respond to buttons or remote, and will not start up.
All higher voltages from PSU get shut down by controller board, and only the +5V remains on.

To attempt resetting the TV, disconnect all video cables, disconnect the power cord, wait about one hour and plug it back.

If TV does not restart, then there may be an internal fault.

In that case leave TV unplugged for longer, just in case.

If still no luck, then call Sony to discuss a repair. The number is listed on your owner manual.

If instead TV will restart, do not use the faulty video cable again, this can damage your TV.

Regards

Nov 06, 2009 | Sony Projection Televisions

2 Answers

I want to find the Sky remote code for this Tv.


Just got an LG 42LH2000 and code 0206 works

May 16, 2009 | LG Projection Televisions

1 Answer

New Sharp Aquos LC37X20E. After 30 mins turns itself off to standby and comes back on after 2-5mins (even though the automatic return to stanby has been set to "disable"). Eventually after...


According to Sharp it is a software problem. Engineer came, installed software update ,10 minute job.....TV worked fine for 1/2 day unfortunately: Then images turned black and white in all channels TV turned itself off, and stanby and OPC buttons started flashing. When TV came back on its own 10 mins later , screen had 2 large square staines superimposed in image (as if it was a burnt screen)...Engineer will be back next week...all quite sad really for a new TV.....will keep u posted

Jul 03, 2008 | Sharp Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...