Question about Bosch HCBG500, 5 Pc Industrial Hammer Drill Bit Set

1 Answer

Drill starts drilling as soon as i insert the battery

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 550 Answers

Replace switch

Posted on Jul 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove battery from drill


Most batteries are held in place by one or two clips. Make sure these are depressed and then try sliding the battery off the drill. It is possible that being new that the battery is slightly tight or that it was not inserted squarely so will need slightly more force to remove, just make sure the clips are depressed.

Sep 17, 2014 | Drills

1 Answer

I bought a draper 500w hammer drill. instructions are not straight forward. I don't know how to get started with it. Do I have to plug it in first and how do I start drilling? C


Plug it in ... insert a drill ... tighten the chuck (the thing you put the drill into) ... pull the trigger ... drill the hole.

There should be a collar around the chuck that will select hammer or no hammer --- or there may be a pin to pull near the chuck. There may also ge a clutch on the collar. Play with it so to say, it will soon be self evident how it works.

The only time you will use the HAMMER setting is when you are drilling with a SPECIAL CARBIDE TIP drill into CONCRETE or other non wood - non metal - conctete or clay product (brick).

Jun 01, 2011 | Vacuums

2 Answers

Battery inserted all the way will not run the drill. pull back 1/4" and it runs ok. thank you


Check contacts where battery goes into drill, could be contact need cleaning on drill and on battery.

Jan 21, 2011 | Makita Drills

1 Answer

Had this battery on charger for months. removed it pluged it into drill and it started getting hot.removed from drill, heat reached 138 degrees before subsiding. this is the second time the same thing...


the battery is supposed to be removed from the charger as soon as fully charged ,otherwise it will cause the battery to malfunction and eventually die

Nov 14, 2009 | Drills

1 Answer

Drill stopped work ing when hot. One drill we bought stopped after 10 6mm holes. The others work when you pull the trigger and then sometime they don't.


Sounds like a burned out motor.

Sometimes you can replace the brushes and make them work again.

When operating that drill, make sure that you are not overheating the motor.

Depending on the material that you are drilling, you may need to use the drill on a slower speed in order to not overheat the motor.

Another way is to have more than one drill, and switch to a cool one as soon as you notice heat on the in-use drill.

If your drill is battery powered, stop using the drill and change the battery as soon as the battery dies enough to slow the speed of the drill.

Operating the drill under reduced power is very hard on the motor for several reasons.

Oct 28, 2009 | Milwaukee Tool Drills

1 Answer

Craftsman power drill - batteries wont recharge. When I insert dead batteries into the charger The green light ''Fully charged'' comes on and stays on. The batteries do not charge as when they are inserted...


the battery's are most likely dead, (like the real dead) after many uses of rechargeable battery's they slow stop holding charge at all, make sure when you get a new rechargeable battery you fully charge it once and fully discharge it once this will increase batterys life time

Sep 27, 2009 | Drills

1 Answer

14.4V Drill Battery Will not Charge


The battery is 14.4 volts so the charger should be 14.4 volts.

Jun 26, 2009 | Makita 3/8" Dr. 14.4V Cordless Drill Kit

2 Answers

Hitachi DS18DL drill quits under load


sounds like your battery is either shorted out or out of charge

Jun 22, 2009 | Hitachi 18V Lithium Ion Cordless...

Not finding what you are looking for?
Bosch HCBG500, 5 Pc Industrial Hammer Drill Bit Set Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Drills Experts

John Trevino

Level 3 Expert

1383 Answers

River bottom

Level 2 Expert

174 Answers

paulcarew

Level 3 Expert

2364 Answers

Are you a Bosch Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...