Question about Washing Machines

1 Answer

Wf540hotpoint washing machine runs the programm for about 10 mins then stops. It then displays error code fo3. can you help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I found the hotpoint web site which enabled me to find the error code F03 which tells me that a thermistor created a possible short circuit.

Posted on Aug 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Samsung washing machine p1453 stops after 10 mins washing and comes up with code error 6E which is not in the manual


They usually stop with an unbalance load or If its a newer model and u use h.e detergent or suppose to be using it, and if u use it or another detergent to much , to heavy many newer washer have a suds sensor and when it detects to much detergent it will shut u down

Oct 03, 2014 | Washing Machines

1 Answer

Error code E20


Turn the dial to off.

Press and hold the start pause and nearest option button to it.

Whilst holding them, turn the dial one notch clockwise.

The machine will beep or flash, let go of the buttons.

Now turn the dial slowly through each position, stop and position 10 (9 clicks after letting go of the buttons) and note the error code displayed.

Continue turning the dial until you get to off.


Now turn to any programme, then, turn to off again.


Finally, turn to a programme and try the machine.


(It is very important that you turn to Off, a programme and then Off again).


Let me have the error code you retrieved if the appliance still doesn't work.

Oct 14, 2012 | Electrolux Washing Machines

1 Answer

Wash cycle over running


the main control is not advancing properly and needs to be replaced,

May 08, 2012 | Bosch Washing Machines

2 Answers

AEG Lavamat W1450 Electronic - after about 10 mins of programme machine is making beeping sound and stopping


this is an errorcode !
try to download a servicemanual,
then you can figure out the exact failure -
like : does not heat up etc. ....

May 05, 2012 | AEG Lavamat W1450 Front Load Washer

1 Answer

Stops into wash displays f 10


F-10 Washing Machine Error Code

Motor control unit (MCU) heat sink failure error code. Thermal sink on MCU overheating.
- Ensure proper clearance around the washing machine.
- Visually inspect motor control board and central control board wire harness connections.
- Test wire harness to motor connection.

Hope this helps.

May 17, 2011 | Washing Machines

2 Answers

Washer has stopped at 26 min with water in the drum. Will not spin or drain. Just sounds like it starts running then stops and repeats.


Good deal your machine is a Series 11.

“”Washer has stopped at 26 min with water in the drum. Will not spin or drain. Just sounds like it starts running then stops and repeats.””

I believe this is the start of a Spin Cycle of that Wash Cycle which Wash Cycle did you have selected?

Are there any error codes to the LED display like dC or uC?

If you stop that wash cycle with the wet load and do a Spin Only cycle will it complete with no error code?

Does the wash tub bang around in Spin Only cycle with the wet clothes load?

Standing by for some feedback and I will try to help.

Here is the Service Manual and parts look up. Can you let me know if you want to try to DIY the fix?

FAV6800A/FAV9800A Service Manual for reference. Sears Parts Direct for reference.

Rich

Apr 11, 2010 | Maytag Neptune FAV6800AW Top Load Washer

2 Answers

After about 10 mins error code H2O is displayed.


the h2o message means the machine isn't getting enough water. check pressure and water intake pipe.

Mar 15, 2009 | Washing Machines

2 Answers

Whirlpool awm 8125/3 fault code FH


Probably too late, but here it goes:
FH means some cicle is taking too long time.
Replace the inlet electrical valve. It probably wont open enough and the water flow is not enough to fill to level in time. This should cost you 10€ and is easily done by anyone.
Just remove the top of the machine (two bolts on the rear and slide to the back), disconnect the valve (electrical and water input and output), push the lockers and twist the valve free.

Feb 07, 2009 | Whirlpool AWM8123 Front Load Washer

3 Answers

Error message when trying to wash


Unplug the machine and spun the drum few times by hand, wait 10-15 min. and plug it back. Good luck!

Aug 06, 2007 | LG WM-2077C Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...