Question about HP LaserJet P2015dn Printer

1 Answer

2015 network printer

How to configure laserjet 2015 network printer

Posted by on

  • Anonymous Oct 11, 2008

    i can connect to my printer it was reset mistakenly and has an ip configuration of 0.0.0.0

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 87 Answers

Hello,

Please perform the following:

Unplug the network Cable:

Cold reset A cold reset changes most system parameters in NVRAM to the factory defaults. However, unlike NVRAM initialization, a cold reset does not reset the page count, the paper tray sizes, language, or formatter number.
A cold reset also resets all the HP Jetdirect settings as well as the printer settings. Use the following procedure to perform a cold reset.

  1. Turn off the printer.
  2. Press and hold the Go button.
  3. Turn the printer on, and continue to hold the Go button for at least 5 seconds, but not longer than 15 seconds. During this process, the Attention LED turns on.
  4. Release the Go button.
    If both the Attention and the Ready LEDs turn on before you release the Go button, you must start the procedure again with step 1.
The printer's LEDs begin cycling. The cold-reset process runs until completion, and the printer returns to the ready state.


Network reset A network reset changes all network system parameters in NVRAM to the factory defaults. During the network-reset process, all button presses are ignored.
Use the following procedure to perform a network reset.
  1. Turn off the printer.
  2. Simultaneously Press and hold the Go and Job Cancel buttons.
  3. Turn on the printer and continue to hold the Go and Job Cancel buttons for approximately 10 seconds, but no longer than 20 seconds. During this process, the Attention light turns on.
  4. Release the Go and Job Cancel buttons. The Attention , Ready , and Go lights begin cycling from front to back. After the network-reset process is complete, the device returns to the ready state.
    If the Attention and Ready lights illuminate before you release the Job Cancel button, start again at step 1.
Now plug in the network cable and then wait for 5 mins.
Then print a configuration page and check the IP Address.

Posted on Nov 03, 2008

2 Suggested Answers

  • 1 Answer

SOURCE: how to connect to network printer hp laserjet 2015 PCL5

I cannot connect to hp laserjet 2015 PCL5. wia network...
im using 64 bit windows 7, and tell me that Windows cant find a driver for HP.........i install driver and nothing........

Posted on May 17, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Canon PIXMA MX700 is not turning on! I have checked all the cords even moved from one outlet to another and its still not turning on. Should I just purchase an new one this model is an old on


Do you have a CD to install this printer? if you do go into MY COMPUTER where you can erase things and erase the printer and its system then shut computer off and restart then reinstall the printer using your CD to reinstall it. Some times you have to delete things and reinstall them to work.

Jan 09, 2017 | Canon Office Equipment & Supplies

1 Answer

How do I connect two computers to my Canon MX3520 printer?


in the control panel where you see add a printer, you have to add the printer to each computer then click on the share printer box

Jan 09, 2017 | Canon Office Equipment & Supplies

1 Answer

Is my new Epson printer compatible with Linux


http://www.openprinting.org/printers

http://www.openprinting.org/printers/manufacturer/Epson

Don't really know you failed to provide the exact model number ????????????????????????????????????????????
see if model number is listed in the above link

Jan 09, 2017 | Epson Office Equipment & Supplies

1 Answer

Can I network Shinco printer s2145


with one of these
http://www.dx.com/p/network-usb-2-0-lpr-printer-server-10-100mbps-ethernet-31570?tc=AUD&gclid=CP-1weaL9MICFRUIvAodEpYAZA#.VKXrgHs_zLk
Only thing is I did not find windows 8 drivers for this printer as standard so you may run into trouble with computers running windows 8 as each computer has to have the exact operating system printer driver designed for its exact operating system .
Unless you can find windows 8 drivers somewhere on the internet

Jan 01, 2015 | Office Equipment & Supplies

1 Answer

Hp laserjet m1522f error 5 turn off and on


Hi, Error 5 is a Scanner error. When turning the printer on, have the lid up so you can watch the scanner movement. Does it move smoothly? It should go through a warm up and you should be able to watch the scanner movement. If there is a problem with the scanner, there isn't a lot you could do except. The service manual says the scanner assembly should be replaced. If it was my printer, I would try to take a closer look at the scanner assembly and check to see if the scanner unit is bound up somewhere, or maybe a drop of 3 in 1 oil on the scanner rails. Let us know what happens.
thanks

Oct 02, 2013 | Office Equipment & Supplies

1 Answer

Prinnter not printing but showing 'put custom in manual tray'


There is still a print job in the queue. Place a sheet so it prints or kill the job.


Open Printers and Faxes. Open printer. Highlight jobs and Right click > Cancel, or Documents > Cancel.
For those stubborn jobs, Right click My Computer > Manage. Choose Services and Applications > Services > Print Spooler. Right click and stop. Then start. This may have to be done from the Print Server if it's network printer. Contact IT to kill.

Nov 09, 2012 | Office Equipment & Supplies

5 Answers

Samsung SCX-3201G printer driver free download


Samsung SCX-3201G printer driver no download plzzzzz help me

Jun 21, 2012 | Office Equipment & Supplies

3 Answers

HP Laserjet 3330. Scanner bulb warming up doesn't go away. I have done the "solution 1" as discribte but nothing is happening. It goes like: - i put the power on, hewlett packard is flashing, the...


How does the bulb look? Is it bright or kind of dim. The bulb warming error is designed to halt use of the machine until the scanner bulb reaches the correct output level. As these are basically a flourescent tube, they will dim over time and at a certain point they will not generate enough light to enable proper scanning. If the bulb is dim, it will require replacement.

Mar 14, 2011 | Office Equipment & Supplies

1 Answer

Problem installing drivers for HP 4355 printer in vista 32bit OS


Vista OEM Cd usually doesnt come with drivers.

Printer should have come with its own cd which contains both the software & drivers.

If it didn't come with any
You can try using windows update
or
downloading drivers from hp site

http://h10025.www1.hp.com/ewfrf/wc/softwareList?os=2093&lc=en&cc=us&dlc=en&product=1138373&lang=en

Feb 24, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
HP LaserJet P2015dn Printer Logo

5,609 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Vinaya Kumar...
Vinaya Kumar...

Level 3 Expert

1121 Answers

Seeker5211
Seeker5211

Level 3 Expert

1088 Answers

kakima

Level 3 Expert

98921 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...