Question about Asrock P4I45GV R5 Motherboard

1 Answer

No beep no display

No beep and no display when i satrted my pc

Posted by on

  • Anonymous Oct 06, 2008

    have power but no beep no display,

  • vher19 Oct 06, 2008

    have power, no beep no display, cpu fan and hdd runs for a few seconds and then stops and then runs normally afterwards.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 233 Answers

Check the power supply then the cpu

Posted on Jul 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MSI N1996 no beep no display.


msi motherboad no beep at all

Jul 14, 2012 | Intel Motherboard

1 Answer

My pc is booting but no display


Did you check your monitor with other system or individually. If it works fine in these conditions then the issue belongs to your pc.
First of all, you have to confirm that is it the problem of VGA itself or the motherboard. For this, you have to see that does system beep when you start it because system with beeps having the error and the beep sound with continuous or 2-3 beeps relate with different issues. I am going to write down the beep conditions.

1 short beep Normal POST - system is ok 2 short beeps POST Error - error code shown on screen No beep Power supply or system board problem Continuous beep Power supply, system board, or keyboard problem Repeating short beeps Power supply or system board problem 1 long, 1 short beep System board problem 1 long, 2 short beeps Display adapter problem (MDA, CGA) 1 long, 3 short beeps Enhanced Graphics Adapter (EGA) 3 long beeps 3270 keyboard card


best of luck!

Mar 13, 2012 | Gigabyte 7VM333M-RZ (GA-7VM333M-RZ)...

1 Answer

I have recently built a new PC with an Asus P8H61-M and upon turning the PC on I am recieving no Visual on either of my monitors


Hello

If this is the first time to turn you on your computer check first the power supply of your computer if connected to their proper connector. Check your memory if clip properly in there memory slot. If you are using Video Card check it if it is properly connected to the connector. Then connect your VGA connector at the back of your computer when you have video card connect the VGA Cable of you monitor to the video card VGA output if does not have connect it with the onboard VGA output. Then press the power switch if the unit is still no visual in monitor try to search or hear a beeping sound in your computer by its on board buzzer. Find which beep you hear from your computer.

No Beep- No Power, Loose Card, or Short.
One Short Beep- Normal Post,, Computer is OK.
2 Short Beep- POST error, review screen for error code
Continues Beep- No power, Loose Card, or Short
Repeating Short Beep- No Power Loose Card or Short
One Long And Short Beep- Motherboard Issue
One Long and Two Short Beep- Video (mono/CGA Display Circuitry) Issue.
One long and three short beep- Video (EGA) Display Circuitry
Three Long Beep- Keyboard/ Keyboard Card Error
One Beep, Blank or Incorrect Display -Video Display Circuitry

Hope this help with your problem. Keep on touch in fixya

Jul 19, 2011 | ASUS P8H61M Intel H61 TX Motherboard

1 Answer

PC power on but doesn't display anything on the monitor and has a beep code of different intervals of time. Here are the beep codes: 2 beeps, after 1 sec, 8beeps, after how many seconds 2 beeps after how...


AMI BIOS beep codes

Below are the AMI BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary.

Beep Code Descriptions Document
1 short DRAM refresh failure CH000996
2 short Parity circuit failure CH000607
3 short Base 64K RAM failure CH000996
4 short System timer failure CH000607
5 short Process failure CH000607
6 short Keyboard controller Gate A20 error CH000383
7 short Virtual mode exception error CH000607
8 short Display memory Read/Write test failure CH000607
9 short ROM BIOS checksum failure CH000607
10 short CMOS shutdown Read/Write error CH000239
11 short Cache Memory error CH000607
1 long, 3 short Conventional/Extended memory failure CH000996
1 long, 8 short Display/Retrace test failed CH000607


For more information go to: http://www.computerhope.com/beep.htm#04

Jan 09, 2011 | EliteGroup P4VXASD2 Motherboard

1 Answer

I cant get the system booting process.


Reset your bios settings pull cmos cell from motherbord for 10 minutes then put it again it's position .Then pull out ram then refit again it.

then check .
If still issue then Change ram may be your ram has issue.
if after change RAM memory same issue then you have to repair your motherbord.
Also check key bord num lock key if it on and off after satrt computer then it is screen resolution issue.
For that when you power up the computer press F8 key then enter in enable vga mode .
Then change display proeprty settings change scren resolution to 1024*768 then aaply and ok.then check.
Also refix processor and processor fan .
Clean all dust from mtherbord and all parts.

Aug 22, 2009 | EliteGroup NFORCE 570 SLIT-A Motherboard

1 Answer

ASUS K8S-MX PC powers up but no display on monitor and no error codes. Hard drives spin and sounds as if it is in boot routine


OPEN UR CPU AND OUT UR RAM FROM MOTHERBOARD AND START UR PC WITHOUT RAM IS IT BEEP OR NOT IF IT BEEP THEN CLEAN UR RAM AND RE INSERT IN MOTHER BOARD AND THEN START UR PC IS IT OK
IF NOT THEN PICOUT BATERY CELL 2032 FROM MOTHER BOARD AND THEN START UR PC

IS IT BEEP WITHOUT RAM AND CELL IF YES THEN CLEAN UR RAM AND RE INSERT IN MOTHER BOARD AND THEN START UR PC
IF IT IS OK THEN CHANGE UR BATTERY WITH NEW ONE

IF UR PC BEEP WITHOUT RAM BUT NO DISPLAY WITH RAM THEN CHANGE UR RAM WITH NEW ONE.

Jul 01, 2009 | ASUS K8S-MX Motherboard

1 Answer

Long beep when power on PC


Usually any kind of clear distinctive beep while booting up is an error code. If you get a long beep with no display then it could be the memory or CPU. Check to make sure all of your cards are pushed in all the way. Just take your hand and push on your memory, cpu, and other cards gently but firmly to make sure they are seated. Also make sure that everything is connected. You may have missed connecting power to something.

Jan 20, 2009 | Foxconn (755A01-6ELRS) (K8S755A6ELRS)...

1 Answer

No Beep No Display


Immediately change your motherboard.

Jul 03, 2008 | Gigabyte 8VM533M-RZ (GA-8VM533M-RZ)...

2 Answers

No Beep No Display


motherboard problem motherboard can't display when switch on, the cpu fan faster no beeping . I had change power supply, but same.Check the keyboard LED,Not flash.I had remove the ram but can't hear beep. PC speaker ok conferm. Monitor display tested monitor its ok . But no comming display. Can you help me? How i can solve this problem?

Jul 03, 2008 | Intel Motherboard

1 Answer

I could not access BIOS or anything else on my computer.


Starting the PC without memory will result in a ?beep code? error, which is the beeping you are hearing. Replacing the memory should make the beeping go away. As far as accessing your BIOS if you PC won?t display anything they accessing your system BIOS won?t accomplish anything. -When you start your PC with the memory installed do you see anything displayed on the screen? -Was the PC operating correctly before your reinstall? -Why did you void the CMOS? -Why did you remove the PC memory?

Jul 23, 2007 | FIC P4M-915PD1 Motherboard

Not finding what you are looking for?
Asrock P4I45GV R5 Motherboard Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asrock Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Are you an Asrock Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...