Question about Vacuums

1 Answer

Pictures on how to change belt on a wildcat vaccum

Posted by on

1 Answer

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=846664
Generic problem for all Vacuums
Pictures on how to change
Posted by dixieldavids on July 28, 2008
Pictures on how to change belt on a wildcat vacuum
Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Not knowing the brand name and model number for the vacuum but I can give you a generic way of changing the belt. You 1st need to remove the bottom plate by screws, levers or clips, then you can get @ the belt, if not then you should remove the top cover and then you can get @ the belt. 1st remove the belt from the brushroll and install the new belt on the pulley side of the brushroll and then use a belt puller or a screwdriver with a bend on the end and then stretch the belt onto the motor pulley and then track the belt in a straight line so that is running in a straight line. Replace the bottom plate and the belt change should be done. Please feel free to contact your local vacuum cleaner dealer in your area.

So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
Thanks, Don the Vac Man
Go Ahead. Use Us.

Posted on Jul 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.


I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!

Eureka Contour 2900 Owner's Guide

Eureka Contour 2900 Belt

Oct 26, 2009 | Vacuums

1 Answer

Vaccum cleaner belt change


If you've put a new belt on and you still are getting a rubber smell, then odds are that your agitator (the rotating brush) is not turning freely, and that means either (a) you need to remove the end caps and remove any hair / debris that is under those end caps, or (2) the bearing(s) of the agitator are bad. Depending on the model of the Sharp (which was not provided), you may be able to order just the defective bearings and replace them (or take the agitator to a vacuum shop to have them do it), or you can (or may need to) order the agitator assembly complete.

May 05, 2009 | Eureka 2961AVZ Bagless Upright Vacuum

1 Answer

Eureka altima stopped power mid vaccuming, have changed outlits


make sure all your filters are clean,try to turn the brush roller by hand a few times if it turns real freely then the belt is broke.if it is reall hard to turn then you have something wrapped around the ends of the roller where the bearings are.your motor guard might be keeping it from running because it got too hot take the brush roller out and the belt let it cool down for 20 minutes then try it without the roller and belt.you should be able to take the ends of the roller off by just pulling out on them so you can remove what ever is in there

Mar 21, 2009 | Eureka Altima Upright Vacuum Model 2996AVS...

1 Answer

Not sucking makeing a clogged noise


Bagless vacuums don't usually get clogged as easily as standard bag styles do. However, if you can disconnect the top half from the brush head section you should see a "neck" where the two meet, check there for a clog. Also check your filters, this is where loss of suction happens most. Dirty filters = Low Suction. I hope this helps

Jan 19, 2009 | Fantom Vacums Fantom Wildcat 2100 Upright...

1 Answer

Vaccum Cleaner


You can download the manual here and it will tell you how to replace your belt. I could tell you, but I won't have diagrams which the manual does. Let me know if you require more assistance.

Dec 10, 2008 | Hoover U5172900 Fold Away Widepath Bagless...

1 Answer

Bissell vaccum cleaner belt change


I need instructions on how to change the belt

Sep 09, 2008 | Bissell 3522 PowerForce Bagged Upright...

1 Answer

Hoover Windtunnel


Your belt may be twisted inside-out. Be sure the printed marks on the belt face away from the pulleys and shaft. The printing should face you.

Oct 22, 2007 | Hoover U6437-900 / U6439-900 Windtunnel...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...