Question about Onkyo TX-NR905 Receiver

1 Answer

Onkyo TX-NR905 Protection Circuit Activated

After hooking up all the components the reciever run but inmediatly turns off and the standby button blinks.

I have disconnected all the inputs and wait for about 3 hours, following the manual instructions. Then i turn on the receiver but it turns off and the stand by button start blinking.

How can i reset my receiver out of Protection Circuit Activated?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,234 Answers

The problem is not with the inputs. This unit is in protect because a problem has been detected in the output section. Try disconnecting the speaker wires and turning it on. If the unit remains on, there is a short in one of the speaker wires. If the unit still shuts down, there is an internal problem that will require repair. It sounds like this is a new piece. If so, it should be covered under warranty.

Keep us posted,
Dan

Posted on Jul 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got an Onkyo amp- TX-SR674, don't know why i turn on it but after 2 seconds, it will switch off and standby light is flashing, can many times. Please help


If the stand by red light starts blinking after 4 seconds of switching On it indicates an output short circuit. In all probability one of the Amplifiers output stage is defective and to prevent speaker damage the protection circuit is getting activated in 4 seconds. You will need professional help to fix this.

Sep 11, 2011 | Onkyo Audio Players & Recorders

1 Answer

My tx-nr905 recievers output audio goes out when connected to my projector and a dvd player, but its ok with any other output combo; proj/sat or tv/dvd or tv/sat etc..... bought new about 4 yrs ago, has...


Semantics maybe, but sources are INputs. OUTputs are speakers, audio to other devices.

A DVD is always an INPUT.

So what's different? IOW, how are the DVD and Projector (Really? It uses a video OUTput) connected for audio? Have you looked at the manuals? Digital sources must be assigned, for example.

Aug 25, 2011 | Onkyo TX-NR905 Receiver

1 Answer

Lost video signal to monitor (TV)


I had the same problem - Onkyo had me reset the unit by holding down VCR and pushing the power button. Make sure you record your settings before doing this - as the unit will be fully reset. This solved the video problem for me.

May 26, 2010 | Onkyo TX-NR905 Receiver

1 Answer

Has trouble getting input signal


This unit has a defective hdmi board,this is a common problem with this model. The unit is to be taken to a onkyo service center for exchange of the hdmi board under warrenty, if out of warrentyit will cost you several hundards of dollars.

Apr 19, 2010 | Onkyo TX-SR606 Receiver

1 Answer

Low Volume regardless of input


Front L/R and Surr back L/R are the termianls used for BI-amping
Check page 27 of the manaul
http://www.onkyousa.com/download/own_manuals.cfm?cat=Receiver
you can find it here

Dec 24, 2008 | Onkyo TX-NR905 Receiver

1 Answer

ONKYO TX-SR606 Single output to TV


Hi there. for your receiver, the only time it can upconvert is when you go out as HDMI. In your current hookup (component out to tv) the signal from your cable (using a composite) will not be able to pass through the component cable. This means you either have to hook up your cable box using a component cable as well or add a composite cable (yellow) from monitor out of the receiver to the tv. Page 22 of the manual will show a diagram of the video signal flow. hope this helps.. ^_^

Dec 02, 2008 | Onkyo TX-SR606 Receiver

1 Answer

Onkyo TX-DS989 not staying on


This sounds like the action of some protection circuit that is monitoring some condition or voltage that isn't within its design limits. If it was mine, I'd look for an Onkyo forum to see if others have experienced the same problem. 

Sep 10, 2008 | Onkyo TX-DS989 Receiver

1 Answer

Onkyo receiver question


One of the speaker maybe are in bad conditions and that burn out the audio amplifier IC you need to change it or send the device to a repair center.Good luck

Apr 28, 2008 | Onkyo TX-SR502 Receiver

3 Answers

Brand new Onkyo Tx-sr605 won't leave stand by


If the unit will not leave standby I would remove all power, disconnect *all* connections at the back, reconnect to a power source and try powering on. This will eliminate any connection causing the Onkyo to stay in standby due to a short. If it still will not enter power-on mode, you may want to look at the power source (is it properly grounded?), but beyond that the unit probably needs to go back.

Nov 03, 2007 | Onkyo TX-SR605 Receiver

1 Answer

Reads PROTECT on the display of my Onkyo TX-SV525 ???


HOWDY,         NOW YOU COULD TRY THIS ONE: POWER THE RECEIVER UP , THEN PUSH&HOLD !THE VIDEO 1 BUTTON, THEN TURN THE PIECE IN THE OFF (STANDBY MODE ) ,IT WILL SAY "CLEAR SO IT SHOULD BE BACK TO IT,S ORIGINAL FACTORY SPECIFICATION,S.

SUCCES !                              AMSTERDAMCOWBOY-HOLLAND-NOW FLORIDA! 4-EVER

Apr 28, 2007 | Onkyo TX-SV525 Receiver

Not finding what you are looking for?
Onkyo TX-NR905 Receiver Logo

Related Topics:

912 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Dennis McCollum

Level 2 Expert

137 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...