Question about Smeg 18 in. STX45-1 Stainless Steel Built-in Dishwasher

2 Answers

Cannot set program

Hi there:

My dishwasher won't let me set the program. The only response I get from the dishwasher when I turn it on is a beep and it stays in P0. Usually, it allows me to set the program it by pressing the "P" button. I can only press the little "clock" button whcih then gives me a "26" on the information screen.

Any ideas?

Thanks,

Julian

Posted by on

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,226 Answers

Hello,

check the the circuit board for error, or clean it ..

also try unplug from the wall and let rest for a while some instance will resolve the issue. however, if the same issue occur then probably the circuit board got error and need to be replaced.

melnavz

Posted on Jul 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Smeg Master
  • 19,396 Answers

Try resetting it by disconnecting the power cable, but at a glance looks like the programmer is faulty.

Posted on Jul 28, 2008

  • Ginko
    Ginko Jul 28, 2008

    I see if I can find out what error code is.

  • Ginko
    Ginko Jul 28, 2008

    E6 is heating detected with no water present,


    check water supply, valves, kink in hose, check that there is no debris in the hose.



×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Elctrolux dishwasher won't start, display won't light and it randomly beeps


Check continuity of the 4 small wires that connect to the control panel to the control board. They seem to break where they flex for the door to open and close.

Jul 25, 2012 | Electrolux EWDW6505GS Fully Integrated...

1 Answer

Miele Advanta dishwasher beeping


Buzzer
The end of a program and faults can be
announced by a buzzer tone.
The buzzer at the end of a program
sounds five times in intervals with a
brief break in between. The buzzer
sounds up to one hour if the
dishwasher is not turned off.
The buzzer for a fault sounds
continuously. The buzzer sounds for up
to two minutes if the dishwasher is not
turned off or the fault is fixed.
The buzzer is activated by default. It
can be set to off, so it does not sound
at the end of a program. The buzzer for
a fault cannot be set to off.
^ Open the door.
^ Turn the dishwasher off o.
^ Press the program button and at the
same time turn the dishwasher on g.
Hold the program button until the
lower right program indicator comes
on.
If it does not come on, start over.
^ Press the program button briefly four
times.
The "Intake/Drain" indicator flashes 4
times in intervals.
The upper right program indicator
shows if the program end buzzer is
turned on or off.
- Upper right program indicator
flashes: Buzzer is turned on
- Upper right program indicator is off:
Buzzer is turned off
it is not easy to disable the buzzer. you have to hold the buttons down exactly the way it tells you to in the manual. you also have to pay attention to the lights and make sure they are flashing the proper sequences. try it two or three times. you will eventually get the hang of it. not sure where you live, but the miele techs have a computer that allows them to disable the beeper if you are unsuccessful. the proceedure is copied below.



^ To change the setting, press the
program button until the
"Intake/Drain" indicator lights.
^ Press the program button briefly
three times.
The setting is saved.
^ Turn the dishwasher off o.

Jun 14, 2012 | Miele Advanta G2170SCSF Dishwasher

1 Answer

GE Dishwasher Won't turn on


Door may not be fully closing for some reason.

Mar 15, 2012 | General Electric GE Profile Dishwasher 24...

1 Answer

Brand New Whirlpool Dishwasher won't start, can't change program eiether


Make sure the dishwasher door is firmly closed, press and hold the start pause button for about 5 seconds, this will clear the cycle, The try selecting a wash cycle and push start.
See if this helps.

Mar 04, 2012 | Whirlpool Dishwashers

2 Answers

My FP Dish Drawer beeps and won't start. The bottom drawer makes the same beeping sound - four quick beeps - as if it were not closed when I try to start it. Dishes are stacked properly and of course...


Hello & Welcome to FixYa

The problem is with the control board that is bad and needs replacement. Please get back to me if you have any other questions.

Kevin

Aug 01, 2011 | Dishwashers

1 Answer

Beeping sound when cycle is finished just started after 8 years. how do I turn it off?


Hello,

Welcome to FixYa.

I think can answer your question..."beeping sound when cycle is finished just started after 8 years. how do I turn it off?"


Follow these steps...

**How to Operate the Cycle Completion Signal**


1. Open door, hold down program button (see
Beeper Table below) and simultaneously turn the unit "ON".


MODEL Program BUTTON

SHU 9950 Delay Start Hours
**SHU 9910-9920 Delicate/Econo** should be yours
SHU 8800/8810 Quick Wash

SHV 6800 Delay Start Hours
SHV 4800 Delicate/Econo
SHV 4300 Delicate/Econo


2. Release program button.
a. For SHV 6803 and SHU9950 models:
The display will blink with a code of "0", "1" or
"2". You are in program mode.

? If the display blinks with a "0", you will hear
no signal (indicates OFF).

? If the display blinks with a "1", you will hear a
LOW volume signal.

? If the display blinks with a "2", you will hear a
HIGHER volume signal.

b. For all other models with the beeper
function:

? If the machine beeps, then the Cycle
Completion Signal has been enabled.

? When you push the button again and it does
not beep, it means that the Cycle Completion
Signal has been disabled.

3. To change the program, press the program
button until the desired setting is selected.

4. Turn the Dishwasher off to take it out of
program mode.

* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.

Hope this answers your question and provides you with what you needed.

Thank you for choosing FixYa and good luck.

Please take a moment to rate the solution provided and a short testimony if you feel it's warranted, but also let me know if you require further assistance.

Regards,

Macmarkus :)

Nov 06, 2010 | Bosch SHU9915UC Dishwasher

2 Answers

How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?


Hello,

Welcome to FixYa.

I think can answer your question..."How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?"


Follow these steps...

**How to Operate the Cycle Completion Signal**


1. Open door, hold down program button (see
Beeper Table below) and simultaneously turn the unit "ON".


MODEL Program BUTTON

SHU 9950 Delay Start Hours
**SHU 9910-9920 Delicate/Econo** should be yours
SHU 8800/8810 Quick Wash

SHV 6800 Delay Start Hours
SHV 4800 Delicate/Econo
SHV 4300 Delicate/Econo


2. Release program button.
a. For SHV 6803 and SHU9950 models:
The display will blink with a code of "0", "1" or
"2". You are in program mode.

• If the display blinks with a "0", you will hear
no signal (indicates OFF).

• If the display blinks with a "1", you will hear a
LOW volume signal.

• If the display blinks with a "2", you will hear a
HIGHER volume signal.

b. For all other models with the beeper
function:

• If the machine beeps, then the Cycle
Completion Signal has been enabled.

• When you push the button again and it does
not beep, it means that the Cycle Completion
Signal has been disabled.

3. To change the program, press the program
button until the desired setting is selected.

4. Turn the Dishwasher off to take it out of
program mode.

* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.

Hope this answers your question and provides you with what you needed.

Thank you for choosing FixYa and good luck.

Please take a moment to rate the solution provided and a short testimony if you feel it's warranted, but also let me know if you require further assistance.

Regards,

Macmarkus :)

Oct 07, 2010 | Bosch SHU9915UC Dishwasher

1 Answer

Beep's incessantly after cycle is complete. How can we re-program it to turn off after one or two beeps?


Hello, welcome to fixya.

To Enable or Disable the Cycle Completion Signal...

1. Open the door, hold down the “Quick Wash”
button and simultaneously turn the Dishwasher on.
The “Quick Wash” light will blink (program mode).

2. While the light is still blinking, push the “Quick
Wash” button.
• If the machine beeps, then the Cycle
Completion Signal has been enabled.
• When you push the button again and it
doesn’t beep, it means that the Cycle
Completion Signal has been disabled.

3. Turn the Dishwasher off to take it out of
program mode.

I hope this answer's your question. Thank you for choosing "fixya".

Please rate the solution favorably if indeed it was helpful, if not please let me know.

Good luck.

macmarkus :)

Jun 28, 2010 | Bosch SHU9915UC Dishwasher

1 Answer

My rogram 2000 dishwasher is beeping and not


Hi

Did anyone answer you on this, my program 2000 dishwasher is doing the same thing. Any help?

Dec 07, 2009 | Dishwashers

2 Answers

Bauknecht GSX4756 dishwasher


I have this problem frequetly - it's an easy one to fix! Just press the programme button which changes the programme setting you want (on my built-in GSX4756 it's the last button on the right) and keep it pressed in until the beeping stops. Then start it again (will probably be on the rinse programme if it's like mine).

Feb 08, 2007 | Bauknecht 24 in. GSFP3988 Built-in...

Not finding what you are looking for?
Smeg 18 in. STX45-1 Stainless Steel Built-in Dishwasher Logo

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smeg Dishwashers Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Cleverer2

Level 2 Expert

298 Answers

paul
paul

Level 3 Expert

772 Answers

Are you a Smeg Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...