Question about Canon PIXMA MP150 All-In-One InkJet Printer

1 Answer

Mp 150 It says that the waste ink absorber is full. What do we do?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

I do not have the reset codes for the MP150, however the reset codes for the MP190 are below and they may be the same .. Please note that this reset procedure may not work for you and it is possible it can render your printer unusable. Good luck...

Canon MPC190
Reset Waste Ink

1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan, Copy, Copy

2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Posted on Jul 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can not figure out how to fix the waste ink absorber in my canon mp 150 printer/scanner


The waste ink absorber is something that is repaired at a CANONUSA.com authorized service center.

Unfortunately, this is not something that the end user is to repair.

Feb 09, 2011 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

My printer shows E 2 7. how can i fix it?


i believe on this model the error code means that the ink tank is full...
http://www.mediafire.com/?s2pa54m5z2wqwru
this is a link to my hosting site where you can download the software reset tool for a the MP models...
To reset waste ink counter at printers canon pixma MP150, MP160, MP170, MP180, MP450 and MP460 there any 2 choice, that is :
  • Start with printer on then run this software
  • Click Reset Main (main) to reset waste ink counter and then click Reset Platen button (additional)
Additional information error codes for the MP models...
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 – Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error – USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

Aug 07, 2010 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

I am receiving a message that my Pixma MP 150 Waste Ink Absorber is full...What do I do?


The unit has to be dis-assembled and the ink absorber (like a felt blotter) has to be cleaned or replaced. After re-assembly, service software is used to reset the ink counter.

Nov 15, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

My Canon Pixma MP 170 tells methe waste ink absorber is full...


It is a shop repair since you have to use Canon diagnostics to reset the count and clear the error. The new part is around $10.00 only.

Jul 01, 2009 | Printers & Copiers

1 Answer

Conon waste ink absorber full how do you replace


canon mp 150 series printer USB 001 The waste ink absorber is full

May 18, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Cartridge jammed / Waste Ink absorber almost full


Hi,
Waste ink pad or pads are full and need changing.
Under your ink carraige cradle it is,
It will be full, bit of a dirty job.

Hope this helps
Ric.


Apr 17, 2009 | Printers & Copiers

1 Answer

Waste Ink Absorber is full


I had the same problem. There is not a replacement. It just need to be cleaned. Take it to any computer repair service. You dont need a Canon Service Center.

Feb 28, 2009 | Canon PIXMA MP150 All-In-One InkJet...

2 Answers

Printers Problem Canon MP 145 code E27


Try this fix.....CLICK HERE

It works the same for the Canon MP 150 or MP 160

Jan 25, 2009 | Canon PIXMA MP160 All-In-One InkJet...

2 Answers

Canon printer PIXMA MP 150


I think this may work.
Reset Waste Ink
1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan, Copy, Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Jun 29, 2008 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Canon mp 130 printer waste ink


hi
am AJAY FROM INDIA
off the printer and open upside cover,see 'the waste ink absorber if there any spunge pull that
and empty the waste ink from sponge or waste ink absorber
ok

again cloused the upside cover
ok

Jan 03, 2008 | Printers & Copiers

Not finding what you are looking for?
Canon PIXMA MP150 All-In-One InkJet Printer Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96372 Answers

old marine
old marine

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...