THE PLASTIC FEMALE END WERE THE LAMP HOUSING PLUGS INTO IS BROKE I CAN'T GET TO IT WITH OUT A SCYMATIC OF THE TV PARTS DO YOU HAVE ONE?

The lamp is defective ,the quality of lamp housing is not good
you need a standard quality lamp with housing
the new lamp with housing USD120
Have a good day!
We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel,
motherboard, powersupply ... with high quality and competitive price.
Jerry Lampdeng Limited
Mobile: 0086-13178867858
Wechat ID: 008613178867858
Whatapp ID: 008613178867858
Skype: [email protected]
http://www.lampdeng.com

this wire is called a molex extender, it's for computer power supplies, clip off the male sides of the wire, the male side will not be used. and after that remove the plastic housing of the female end and now adjust the size of the circular connectors with pliers to fit with the connector for speaker input and strip wire ends that's it

Look for socket to be bent or moved out of position---happens when replacement lamp is installed.

you can find the parts nyou need at any lowes or home depot they will carry these parts if your by a tractor supply store try there to, good luck,

Most of the time the female end of the connector comes right of a part called the ballast. Ballast's are replacable. Is the aluminum melted? I am not sure where to purchase the ballast. The female connectors is ussally atached to frame with screws or sometimes clips

I have a sony KDF-42E2000 and our lamp went out a yr after we purchased it. I found the lamp with out the housing on eBay and there was a video on how to take the old lamp out of the housing and replacing it with the new lamp. Now I am a female with NO experience with doing that type of thing, but I was able to do it with ease. So you can swap just the bulb. Also we just had to replace the lamp again and this time on eBay there was the lamp with the housing for 91.00. Easy as pie... But now the problem is that there is a red band across the top of the screen. Just got off the phone with Sony and they said that to fix it, it was going to be around 1K but they will let me choose between 2 different TV's at a reduced price. Apparently there has been a lot of issues with the TV's to the point where this is what the specify in the email: In consideration for Sony making and you accepting this offer, you agree to release and hold harmless Sony Electronics Inc., and its affiliates, officers and directors from any and all claims for damages, loss, cost, expense or liability both known and unknown, which you may have incurred in connection with your television.
So no matter what you decide as far as lamp vs lamp and housing, be aware you might end up contacting sony at 800-200-SONY to get an offer of a discounted tv.... Good luck!

there should be 2 plastic plugs that have a standard screwdriver slot in them,they should be towards rear end of drill,the plugs are flush with the plastic motor housing

Welcome to FIxYa.com

Parts:

3157 Brake light

How to Remove bulb:

Remove the Lamp unit from the end of the quarter panel.

"Open tailgate to access and remove the two screws that secure the inboard side of the rear lamp unit to the side of the tailgate. (see Figure) Pull the outboard side of the rear lamp unit rearward (away from the end of the quarter panel) far enough to unsnap the two ball studs on the outboard side of the lamp housing from the plastic nuts in the quarter panel."

Change Bulb:

See Figure

Regards, Lee Davidian

Thank you for using FixYa.com

Listen closely. The tv should make a high pitch whine as it turns on. If it does wait and see if it tries this a few times. If yes then check the bulb, I have seen cases where the lamp shoves the power connector back into the set. If the tv starts with a grown or heavy vibration noise, then your color wheel may have broken and needs replaced.

HEY SAM SOUNDS LIKE THE LAMP IS NOT THE ONLY ISSUE,IT COULD BE YOU'RE 5 VOLTSUPPLY IS LOW THE ONLY WAY TO BE SURE IS TO REMOVE THE MANY SCREWS HOLDING THE BACK ON AND ALSO REMOVE THE METAL SHEET TO GET ACCESS TO THE PLUGS ON THE LITE ENGINE AND USE A VOLTMETER TO TEST FOR 5 VOLTS. IF YOU FIND IT IS IN FACT LOW YOU'LL NEED TO REPLACE THE 6 CAPACITORS THAT YOU WILL FIND HAVE AGED (THEY LOOK BUBBLED) THAT ARE ON THE POWER BD. GOOD LUCK. JOE TV