Question about Mitsubishi CS-35207 35" TV

1 Answer

Receiving satelite I purchased a 'universal' remote for this TV, and after fiddling with the menu/set up, I can not now get the TV to the page/channel that will show the satelite

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Contacted satelite provider, they reset the channel for reception.

Posted on Jul 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have aa Lc19DV220 sharp tv i need to access the menu so i can get the channels but i have a universal remote how can i get to the menu on my tv if it doesnt have a menu button.


To select its inputs, you should have its original remote control. To buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one.
http://electrohelponline.blogspot.com/

Feb 01, 2016 | Sharp Standard (CRT) Televisions

1 Answer

Panasonic CT 27 SL - 13 GL how to connect external speakers


This TV is set up to connect to an external amplifier which that controls the speakers. It has an analog audio output which means you need an RCA audio cable (2 RCA plugs (red and white) on each end. You can't directly connect a set of speakers. The audio output jacks at between the antenna in and the video inputs. Then you need to enter the menu and enter the Audio submenu. Go to the Speakers item. Turn the TV speakers to off and fixed audio out.(The amplifier will adjust the volume.) Use the Up/Down arrows to navigate through the menu options, press enter to enter a sub-menu and the volume up button to change a setting.

There is also a headphone jack which may be compatible with computer speakers. That has a 3.5 mm jack. To use headphones, set the Speakers Audio item to TV speakers Off and variable audio out. (The TV controls will adjust the volume.)


To use a Universal remote to set the audio or modify the channel list, you need one that matches the Menu function of the original remote. You may need to try multiple codes for Panasonic TVs to get the button to work. Some low-end universal remotes may not have the menu button; get a different remote or use the menu button on the front panel of the TV.

To set the channel list, press Menu and select Setup. Go to the Prog Chan option. Then set your Mode in the first option (Cable or Air). Then choose Auto Program to scan all channels or Manual Program to edit the channel list.

The manual for the TV is available at retrevo: http://www.retrevo.com/support/Panasonic-CT-27SL13-TVs-manual/id/275ag210/t/2/ . You will need to enter a code to access the manual. See page 5 of the manual for the input connections (page 7 of the PDF).

Cindy Wells

Sep 13, 2012 | Panasonic Standard (CRT) Televisions

1 Answer

I have no remote..... I cannot get picture only snow. I have Direrct TV..........I do not understand how the channel, volume and menu button are to be usd


If you are using cable wire from your directv receiver and not the red white and yellow wires, you must have the tv to channel 3 or 4 to pick up from the directv receiver. Go to the tv since you don't have a remote and push the channel up or down button to put the tv on channel 3. Be sure the satelite receiver is on.

Jun 09, 2011 | ESA ET432E TV

1 Answer

Not receiving my local cable stations


You need to make sure the TV is set for "cable" tuning and not "standard" or "air." (If you are getting only local off-air channels and no cable stations at all, be sure you have a good cable and connection to the set. Normally, even if the TV is set for "air" you will get the low-number cable channels 2-13.) This is usually a selection through the TV's set-up menu. With a universal remote, it may be difficult or even impossible to get to all the menu entries. Most replacement remotes don't support all the original remote functions. Try with yours and good luck. Once you get the TV set to the proper tuning, you should have all your cable channels.

Jan 03, 2009 | Durabrand BH1304D 13" TV

1 Answer

I lost Orion 13" Model TV1318 remote.Need to menu button access


you can purchase a advanced universal remote or you can go through the menu manually on your set

Dec 14, 2008 | Orion1934 19" TV

1 Answer

Menu keys not working & Chanel 2 & 3 Only


Greetings Eagle7eye,

It sounds like you might have a problem with the cable settings for your TV. There are a few standards for cable broadcasts and you may need to set it to standard or "STD". But since your menu button doesn't seem to be working this would pose a problem.

I would try and access your settings with the universal remote and look for something like antenna (ANT) and change it from air to cable. Depending on how old your TV is too there may be a small switch near your coaxial connection for the cable setting.

Good Hunting.
Jon
Go Ahead. Use Us.

May 05, 2008 | Zenith B32A24Z 32" TV

3 Answers

Toshiba 24AF44


You need the original remote controller to be able to switch input modes.Universal ones usually don't work. If you don't have the original remote and can't find it ever or if it is too expensive you can buy an rf modulator ( very cheap) and connect your dvd player, game console etc) to the modulator then connect the modulator to your antenna with a coax cable. This worked for me. It placed the connection to channel 4 and other cable channels are still working,

You can buy the RF Modulator from: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=180299245670

Mar 16, 2008 | Toshiba 24AF45 24" TV

2 Answers

Won't receive channels above 18, cable not at fault


Your "tuner" in the menu is set on "off air" or "antenna. It should be set on "cable" or "dish". See if you can go into your menu with the buttons on the set and change your tuner setting. Keever

Mar 06, 2008 | Sharp 27L-S100 27" TV

2 Answers

Zenith h32h38dt 32


The "H" model Zenith TVs are hotel/motel sets designed that
a roomer cannot access the menu feature. Your best bet would
be to purchase a name brand universal remote which has the
menu button feature or order an original Zenith master remote
which would not require programming. Once you have a workable
remote which will allow you to access the on-screen menus you
should be able to program the channels.
Hope this helps,
CaseyBee

Feb 27, 2008 | Standard (CRT) Televisions

1 Answer

Channel selection woes continue!


Sorry but your going to need to get an original remote from a friend or relitive to program this set. They sell rca universal remotes for 10 to 15 bucks that will work for you too.

Sep 18, 2006 | RCA F27628 27" TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68301 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Mitsubishi Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...