Question about Samsung Phones

1 Answer

I have some addional hand sets to register to my Samsung SP-R6100 cordless telephone base set. I followed the instructionsup to "Please wait" and it then registers "Failed to Register". It doesn't get to the point of asking for the Authentication code. What am I doing wrong? The handset now registers "Failed to Register" all of the time, even when it is it's base unit.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Code is 9234.

Posted on Apr 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PURCHASED USED SIEMANS 8800 HAND SET ,REPLACED BATTERY,AND RESET PIN TO DEFALT 0000, PHONE FLASHING "SEARCHING" .HOW DO I GET THE HAND SET TO SYNK UP TO THE BASE STATION?


You need to register the handset to your base to get the phone to work to do this follow the steps in the manual. If you do not have the manual go to the link below and scroll down to product detail then click on the blue product manual.

Gigaset-Accessory-Cordless/dp/B00005UFDR">http://www.amazon.com/Siemens-8800-Gigaset-Accessory-Cordless/dp/B00005UFDR

Or look below to learn how.


    
jyackle5_61.jpg

Jun 03, 2011 | Siemens Gigaset 8800 Cordless Expansion...

2 Answers

I have purchased a SL82318 Handset. I have a SL82318 system, with all three original handsets working perfectly. This fourth handset displays: "Connecting..." and nothing else. According to...


*331734#Menu Select on the handset should de-register that handset from the old base, then you can register it to the base as per the manual (put it in the base and hold down the handset locator button for 4 seconds)

Jan 04, 2011 | Vtech SL80108 1.9 GHz 1-Line Cordless...

1 Answer

Searching and out of range message keep appearing. Can't dial out or receive calls Uniden Dect 6.0 (both phones) Tried to register base but unsuccessful.


Hi,

This is because of the following reasons

1.The handset is far away from the base unit.Try to bring the hand set near the base unit and try.
2.The base unit is not plugged in to the power supply.Please check it.

Thanx

Jul 27, 2010 | Uniden DECT 6.0 Cordless Telephone...

2 Answers

I have a Pansonic kx-tga270s that is registered to a base I do not have. Is there a way to deregister it.


you dont need to deregister it if you have not registered all 8 hand sets with your base unit. Just register the new one and the base will assign a new # for this new. I you had registered 8 hand sets with your base already, you need to remove(deregister0 one handset from your base(it can take only upt 8).
If it still not registering please deregister as follows:
on the base unit, press program, them mute, then enter 335#, then enter the handset number you wish to deregister.
after deregistering try to register your new hand set.

Nov 19, 2009 | Panasonic KX TGA270S Cordless Expansion...

1 Answer

Handset No2 displays out of range message


Please check that you have correctly registered the second handset to the base. It may be necessary to de-register the second handset and then re-register it. "Out of range" just means the second handset is not within range of the base phone it was registered to.

Mar 08, 2009 | Uniden TRU8885-2 Cordless Phone

3 Answers

Uniden dect6.0 handsets do not operate


I am writing for my Mum, who is 99. We live far apart, so it is a bit difficult to fix her problem. She had a new Uniden DECT 60 (?) installed in early July. It seemed to be working fine when we left her, but she says it only rings twice before going to voice mail. She says it has always been like that. How can we fix this for her even though we live at a distance?.

Mar 12, 2008 | Uniden DECT 6.0 Cordless Telephone...

2 Answers

My new hand set will not detect my base


Have you followed the instructions for handset registration? For some of the newer handsets, you may need to refer to the instructions that came with the handset (and not the base) instead of just putting the additional handset in the base to register it.

Page 23 of the 9480 manual gives explicit registration instructions.

Jan 07, 2008 | Uniden TRU9480 Cordless Telephone

2 Answers

Caller ID Problem on the GE2811 Twin cordless phone system


How to get the caller ID to work on the additional GE DECT phone handsets. You must follow these steps in the exact order :
#1 - unplug the base phone
#2 - unplug the telephone line from the base phone
#3 - remove the battery packs from the phones
#4 - wait 10 minutes. reverse the order when assembling. Put battery packs in phones, put the telephone line back in the base phone and lastly plug all phones back in.
It takes about another 10 minutes after that before all phone handsets start recognizing caller ID.

Oct 23, 2007 | GE 28111 Cordless Phone

Not finding what you are looking for?
Phones Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Phones Experts

Yoav Shilon
Yoav Shilon

Level 2 Expert

101 Answers

Dakshinamurthy...

Level 1 Expert

23 Answers

Lawrence Oravetz

Level 3 Expert

7565 Answers

Are you a Samsung Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...