Question about Projection Televisions

1 Answer

My mam has a lcd tv it has worked fine for 5 months now it wont recieve any channel on annologue or the built in digi box

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 372 Answers

Hi.

What make & model is the TV set ?

http://dysonmanuals.llc.nu/

Posted on Jul 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to hook up converter box to Westinghouse flat screen the converter is magnavox sdtv. I get autoscan but no channels are found. I do not have an antennae. Do I need one? Help!


If ur tv a LCD tv it is a digital tv.U do not require a Digital converter box to get the new DTV free air signal broadcasting tv channels stations.But u do require a good digital antenna for it to recieve a long an strong signals to recieve a DTV free air broadcasting tv channels stations.

Dec 07, 2010 | Philips Magnavox 50ML8105D 50" HDTV DLP TV

2 Answers

My ILO 26HD LCD tv want get but one channel


You may have to enter the "Menu" of the TV and run the set-up for the cable/antenna connection. This will scan channels and program them to the TV, then you can access them.

Failing that you may have a bad tuner, unplug the TV for a few minutes then replug it and try again.

Hope this helps!

Cheers,

Jan 23, 2010 | Projection Televisions

1 Answer

I have a HD1080,it won't recieve all the digital cable channel


Make sure that one tv doesnt have a built in digital box and the other doesnt because if so, thats why one gets more channels than th other, otherwise, do an auto channel scan, both using the Visio and the HDTV from the same antenna output, if your still missing channles on the HDTV yo u may have a faulty RF receiver on your HDTV. I hope this Helps. Good Luck.

Nov 25, 2009 | Projection Televisions

1 Answer

Sony 60in Grand Wega Channel Guide comes up/Screen goes Blank


u may have a bad cable box ( drectv) try a dvd player on the tv if it work fine that means u have a bad cable box ( drectv)

May 08, 2009 | Sony Grand WEGA KDF-60WF655 60" Rear...

1 Answer

Recently installed two Philco TB100HH9 Converter boxes. Both worked well at first then both lost a major local TV station within days and cannot reprogram it into the box. Have two other TV's without a...


I just had a similar problem with this box - For the first month or two, I got the local NBC affiliate (KING-5 in Seattle) just fine on 5.1, then, after fiddling with my antenna setup, I lost it completely - NOTHING I could do would get it back. I tried a bunch of stuff - Multiple types of antenna, adding an antenna amp box, a handful of "homebrew" antennas - Nada. Yet all my other channels came in fine (although a couple were right on the edge - This box seems to need a "17" or higher on the signal strength - Some of my channels were reading in the 15-18 range, and suffering the "blockies" and sound dropout)

After hitting TVfool.com, found out that the KING digital signal is actually broadcasting on channel 48. Punched in 48.1, and there it was, clear as a bell, using nothing but a "wick" antenna (Basically, strip 4-1/4 inches of the outer braid off one end of a piece of co-ax cable, leaving the center wire alone, then plug the other end into the box) getting me a 23 signal strength. But a second or two later, the box is displaying "5.1" - Weirdness...

Reconnected a near top-of-the-line Winegard Yagi/Log-periodic antenna - VERY directional, and has some gain all by itself - and the signal jumped above 50.

Still couldn't "channel-up/channel-down" or punch in "5.1" to tune it, though - Channel 5.x was a "dead zone" as far as the box was concerned.

Re-did the "autoscan", and now, it's back to normal - I can channel-up/channel-down to it at 5.1, or I can punch it in as 5.1, or I can punch it in as 48.1, and it's all good.

So, try re-doing the auto-scan. Worked for me...


Dec 01, 2008 | Philips Projection Televisions

2 Answers

Do not understand how to set up my alba digi box to my television and recieve basic digital channels help!


Hi.

Ok
1) plug aerial in to the antena in sock on freeview box.
2) plug short aerial type lead in to rf out socket on freeview & antena in socket on TV.
3) plug A scart lead in to the socket marked TV on freeview box & the other end of scart in to one of the scart sockets on the TV.
If your TV has more than one socket plug it into the one marked AV1 or AV2.

4) plug in freeview to mains electricity & switch box on.
5) Turn TV on freeview should appear automatically if it doesnt look on your TV remote for A button marked AV or a button with either A circle or square with an arrow going through it you may need to press this several times until you see digi picture come up.
Thats basically it but do check that you dont need a new aerial etc to be able to get digi signal in your area.

http://dysonmanuals.llc.nu/

Jul 26, 2008 | Projection Televisions

1 Answer

Off Air?


The Scientific Atlanta box was a cable box and recieved CATV signals. The Direct TV box is satellite only. You might check if it has a built in ATSC tuner for off air digital signals. Direct TV in most locations offers the major networks in HD format.

Jan 04, 2008 | Sony Grand WEGA KF50WE610 50" Rear...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...