Question about Insignia LCDTV26 26 in. Television

1 Answer

Insignia tv 26 LCD tv/dvd combo problem

How do I get rid of "No Database" on my screen?

Posted by on

  • leadfoone Jan 18, 2009

    I have the same problem. Sucks I didnt figure out it was a problem while the thing was in warranty.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have an Insignia 26' LCD TV with a built in DVD player and all I get on the screen is a box that says No Database.

Posted on Apr 14, 2009

4 Suggested Answers

  • 91 Answers

SOURCE: User Guide for NS-LTDVD26-09 SKU: 8632937

Go to

this page on the Insignia site

and click on the link to start downloading the user manual.

Don't forget to rate this solution once you've tried it !

Good Luck.

Posted on May 20, 2008

  • 122 Answers

SOURCE: how do we take the stand off of a 26" Insignia flat screen tv/dvd

Look on the back - there are screws holding the stand mount

Posted on Jan 09, 2009

ginko
  • 19396 Answers

SOURCE: 26" Insignia LCD TV will not power up. Green Light Blinks 1x

If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Posted on Apr 19, 2009

  • 1 Answer

SOURCE: No Signal No Database

In your TV Menu select "Channel." In this list you must now select "Auto Scan" then select "Start to Scan." Wait for the scan to complete, this should solve your problem.

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black box in middle of screen


that is probly the closed captio is on get to your menu and turned off..
hope that help

Apr 12, 2010 | Insignia 19 in. Widescreen Flat-Panel LCD...

3 Answers

Insignia 26 inch TV/DVD Combo produces strange odor when on.


You should never have an acrid or burning smell coming from electronics. I'd return the unit, if that is still an option, as it is about to fail.

Feb 13, 2010 | Insignia IS-LCDTV32 32 in. Television

1 Answer

Toshiba 26 inch lcd tv/dvd combo lost picture


I have same problem with a 7 month old Toshiba 26LV610U LCD TV/DVD combo.

Feb 10, 2010 | Toshiba 26HLV66 26 in. LCD TV/DVD Combo

1 Answer

My insignia NS-L26Q-10A 26" LCD television is showing that it is 420i on the screen and I understand that it is supposed to be 720p. How do I change this?


This may have to do with the settings on your DVD player or cable/satellite box. Change the settings on those devices to output the desired resolution (720p) and adjust your TV settings appropriately. More details about the TV settings can be found in the owner's manual.

Dec 29, 2009 | Insignia NS-L26Q-10A 26 in. LCD TV

1 Answer

No Signal No Database


In your TV Menu select "Channel." In this list you must now select "Auto Scan" then select "Start to Scan." Wait for the scan to complete, this should solve your problem.

Aug 23, 2009 | Insignia 42" LCD Flat-Panel HDTV

1 Answer

26 inch insignia dvd/tv combo stuck in dvd mode and buttons and remote won't change or do anything


This is a long shot but, there may be a reset button on the back of the tv if not try unplugging it over night.

Good-luck
Rob

Dec 07, 2008 | Insignia LCDTV26 26 in. Television

2 Answers

"Alarm" wake up


Not all TVs have this function. Have a brand new HP LCD 42" TV, doesn't have the function available.

Jul 07, 2008 | Insignia 26 in. LCD Flat-Panel HDTV

1 Answer

Insignia LCD TV


I think I have the exact same T.V... Uh are all the chords hooked up in the right places? Or are you trying to play games on it and it says it?

Jan 28, 2008 | Insignia LCDTV26 26 in. Television

Not finding what you are looking for?
Insignia LCDTV26 26 in. Television Logo

Related Topics:

512 people viewed this question

Ask a Question

Usually answered in minutes!

Top Insignia Flat Panel Televisions Experts

Sp Gupta

Level 3 Expert

667 Answers

Gareth Cockram
Gareth Cockram

Level 3 Expert

657 Answers

The Wyzzyrd

Level 2 Expert

83 Answers

Are you an Insignia Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...