Question about Kenmore 15529 Built-in Dishwasher

Open Question

Dishwasher not coming on

My Kenmore dishwasher just stopped working mid-cycle. There is water sitting in the bottom and it won't turn on. Is there a reset button on this thing anywhere? It seems strange that it just quit with no warning.

Posted by on

  • Anonymous Nov 10, 2008

    I have the same problem - the built-in Kenmore dishwasher just stopped mid-cycle, prior to the opening of the soap dispenser, and won't do a thing. If I turn the knob fully around the cycle, the light never comes on and nothing happens (except that it did trigger the opening of the soap dispenser). I would love to know if there is a fix for this. (I'm not positive this is the right model, but it's 7+ years old and I can look up the model number after work.)

×

6 Suggested Answers

COXY
  • 76 Answers

SOURCE: Kenmore Model 16253 - Stops mid cycle

Sounds to me that the heater is not working, if you have just bought it, it must still be under Guarantee so go back to the supplier.

Posted on Nov 18, 2007

  • 1003 Answers

SOURCE: Kenmore 587 High Temp/Heat Dry lights flashing, cycle not complete

REPLACE TIMER

Posted on Jan 18, 2008

  • 205 Answers

SOURCE: viking dishwasher quit working

Possible bad door switch, thermostat or timer issue, call for service, make sure the tech. knows how to fix Asko dishwashers as that is what is in on the inside. Be sure that you are getting power to the unit.

Posted on Jul 21, 2008

  • 1 Answer

SOURCE: kenmore elite dishwasher stopped in middle of cycle

My Smeg (never buying brand again) dishwasher UKSTX1 has error message e9 not covered in manual

Posted on Jan 26, 2009

  • 530 Answers

SOURCE: kenmore 665 no lights on panel water in bottom

This is commen with these. you need to take the door and remove the screws around it. You need to gain access to the controller. on the controller you will see a white peice with 2 balck wires going to it that is your fuse. replace this and that will solve your problem.

Posted on Jun 02, 2009

  • 297 Answers

SOURCE: Kenmore dishwasher model 665 stalls in mid cycle

you have a clog somewhere.

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore elite dishwasher stops mid cycle


I assume you mean it stopped in mid cycle and is now dead. If this is the case you will need to turn off the power to the dishwasher and remove the screws holding the front control panel There is a thermal fuse clipped to the front of the control panel Check it using an ohmmeter or continuity tester If it is open you will need to replace it with a kit containing the fuse and wire connectors Do not replace just the thermal fuse the problem will surely return. Also inspect the control board for burned areas.If the control board is burned you should replace the wiring harness with the control assembly

Jan 25, 2014 | Kenmore 24" Built-In Dishwasher with...

Tip

So your Dishwasher sits and "Humming" cannot turn off, no response.


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You should NEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.

on Mar 27, 2010 | Dishwashers

1 Answer

My Kenmore Elite dishwasher just hums when we start it.Its not starting and no water is filling up


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You should NEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.

Aug 09, 2010 | Kenmore Dishwashers

1 Answer

My dishwasher fills, but won't start running. it just sits full of water and just hums.


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.

Apr 14, 2010 | GE 24 in. GSD1000G Built-in Dishwasher

1 Answer

Water in bottom of dishwasher, how do i drain & reset?


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.

Apr 04, 2010 | Dishwashers

2 Answers

Kenmore disposal hums, nothing jammed, everything moves freely, but wont spin. reset button stays tripped & wont catch


Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.

Apr 03, 2010 | Kenmore 13742 / 13744 / 13749 Built-in...

1 Answer

Water sitting in the bottom of washer, and will not cycle


Check your vent drain or your Garbage disposer connection and make sure it's not plugged.

Nov 21, 2008 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Kenmore dishwasher 587.15159400


to whom it may conern:
about six month ago I purchese the dishwasher, But It just stopped working, the green clean light just blinks all day and night, but wont start it's, when I push the red start button comes on but turns off about 5 seconds later turns of, and wont run and clean my dishes. Could you please help me get strat the dishwasher to start up and run again. Thank you patrick c smith

patrick c smtih
phon 951 805 5187
19050 rockman street
lake elsinore, ca., 92530
actt, 5049 9485 2176 1660

Aug 13, 2008 | Kenmore 15769 Built-in Dishwasher

1 Answer

Kenmore Model 16253 - Stops mid cycle


Sounds to me that the heater is not working, if you have just bought it, it must still be under Guarantee so go back to the supplier.

Nov 18, 2007 | Kenmore 16253 Stainless Steel Dishwasher

Not finding what you are looking for?
Kenmore 15529 Built-in Dishwasher Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...