Question about Mitsubishi WD-52525 52" Rear Projection HDTV

1 Answer

Picture jumps after a few hours turned on

After a few hours the picture, which is perfect will start too jump up about a half inch or so. At frist about once every minute, but after about half hour will be jumping every few seconds. The picture stays perfect but this second image is up and back down in a blink of an eye.

Posted by on

1 Answer

I have a 3 yr old 55 inch mitsubishi TV and when I turn it on the green light starts flashing and I must reset the TV about four times before it finally comes on has anyone had this problem if so what solution did you have?

Posted on Jul 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Samsung 23 inch LCD tv works fine for 25 minutes then the screem starts jumping..


There is a Anynet Setting under the input tab. It has to be on the right setting or the picture Jumps after 20-25 minute. Once I adjusted it to the right setting it stopped jumping and it now works Perfect. Would nt have figured it out if I wouldnt have been messing around with it as a last chance deal.

Dec 27, 2009 | Samsung LN-R237W 23 in. LCD Television

1 Answer

Black picture


there is a loose connection in you PCB , shut off the tv unplug it, then open the back cover remove the PCB. turn it upside down. Resolder the semiconductor leads. all

Jun 22, 2009 | Panasonic CT-35G25 TV

1 Answer

Picture jumping


If this jumping is accompanied by a sharp snapping sound, it may be the high voltage circuit discharging to chassis. Leakage can cause the jumping and a discharge can momentarily blank the picture.

If you want to try a 'cleaning cure,' I suggest you pull the plug (not just turn it off) for several hours, preferably overnight. Sets of this size can carry enough static charge to punch a hole through your thumb if you get careless.
Remove the rear housing (shouldn't be more than 6-8 screws) and using a clean paintbrush, and possibly a vacuum to **** up the dust, clean it well and pay special attention to the area around a largish misshapen black plastic object bigger than most anything else and connected to the back of the picture tube via a fairly thick cable.     

Dec 09, 2008 | Televison & Video

1 Answer

Picture jumps


you might have bad caps or the vertical output integrated circuit, try to locate the vertical ic and check the surrounding areas for bad capacitors.


good luck


caypianan@yahoo.com

Oct 23, 2008 | Hitachi 53SWX10B 53" Rear Projection...

1 Answer

I have a 50 inch hitachi ultravision that has no picture or sound but power light is on


Probably a 'cold or detatched' solder joint on a component on that perticular circuit board you are 'wedging' with a plastic rod.

Apr 16, 2008 | Hitachi 43UWX10B 43" Rear Projection...

1 Answer

Jumping picture


Resolder the vertical output IC and the vertical yoke connections on the main PCB

Mar 16, 2008 | Mitsubishi VS-45607 45" Rear Projection...

1 Answer

I have a 50 inch hitachi ultravision that has no picture or sound but power light is on


you have lookse connection on the video convergance amp ic

KIT10 $29.50
Repair Kit for Hitachi convergence Chassis DP-14G
KIT10 Includes 2 pcs STK392-150 , 1 each of the following 1W axial lead fusible resistors:


http://www.digitalhome.ca/forum/showpost.php?p=564268&postcount=220
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html

Nov 04, 2007 | Hitachi UltraVision CineForm 55VG825 55"...

1 Answer

Toshiba 42H81 - Constant jumping picture on scren


it needs the hyper module replaced might as well have em do the stk packs too its too old to be a lemon the part that was replaced was not new it was in someone elses tv and had problems there too the trick is to find someone that will fix it so it lasts

Dec 05, 2006 | Toshiba 42H81 42" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

72670 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...