Question about Philips Magnavox 51MP392H Rear Projection Television

2 Answers

I have a Magnavox 51" Projector TV. Model 51MP392H/17

Hi,
I have a Magnavox 51" Projector TV. Model 51MP392H/17.The TV does not
turn on when I hit the power button. The only thing that does happen is that
when I do hit the power button, the button itself turns a solid red for a few
seconds then it flashed red for another few seconds then it goes off. Any take
on this? Thank you

Posted by on

2 Answers

Well I forgot to mention that when I do turn on the TV the button flashes 9 times then pauses for a second and repeats the flash 9 times over again.

Is this a error code for the 51MP392H/17 ?

Thank you
Joe

Posted on Jul 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,139 Answers

Hello bullmuscle,

This is a power supply problem, I would suspect the HV power supply because the primary and secondary supplies anymore are tied to the HV power supply. This type of repair requires certain pieces of equipment, to test voltages, look at signals, and to if need be test for shorts in inductors (Switching PS transformer and Flyback transformer). I would not recommend that you try to fix this yourself, The cost for this type of problem is not that expensive and can be done in one evening, if the parts are available. You may be fortunate and it could be just a blown fuse, in the HV or LV power supply circuit

I hope this helps,

Thank you,

Shuttle83

Posted on Jul 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Magnovox HD TV Progressive Scan (Floor Model) TV


You can find a replacement Philips/Magnavox fresnel screen, in stock, for this model (51MP392H/17) at this following link from a major parts distributor:

Philips / Magnavox 51MP392H Replacement Part Fresnel Screen

And here's a link for the Lenticular (middle) Screen, if needed:

Philips / Magnavox 51MP392H Replacement Part Lenticular Screen

Jan 16, 2009 | Philips Magnavox 9P6034C 60" Rear...

1 Answer

No Picture No Sound Magnavox Rear Projection Television


51MP392H/17

Actually I have this TV and you need 2 Convergence IC's STK392-120's (120's and 150's will work) of course order 2 of the same type I'm using replacement 150's they allow for a little higher heat and were cheaper ALSO you need to replace the 12 resistors with 6.8 ohm metal film resistors, make sure they are metal film! don’t skimp out here I did and then they blew and fried my IC's and I had to replace everything again!

Great reference link that I posted pictures on, check out page 3
http://www.techlore.com/forum/thread/16736/Magnavox-51MP392H-17-51-quot--TV-has-double-vision/

Where I got all my parts that worked:
Suburban Electronics http://www.suburban-elect.com/

Manual Library you should find all you need here:
http://www.techlore.com/group/2/list_downloads



What you need:
(2) STK392-120 OR STK392-150 IC chips
(12) 6.8 Ohm Metal Film resistors
set of star screw drivers
15 watt pencil solder pencil, DO NOT use a high watt iron you will fry the surface mounted item.
good leaded solder, and flux


BTW if you don’t plan on trying this and are going to throw out the TV, I still need a IC convergence board for a 51MP392H/17 TV I'm fixing, I'm willing to pay S/H and buy your IC board that’s not been tampered with. Edwinkraus@hotmail.com

Nov 11, 2008 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

Magnavox 55'' Projection - Sides come in and out


sounds like Convergence issue.... I have some pictures of the bowing picture TV on the link below...

I'll post you my general message which is for a similar Philips Magnavox 51 inch TV, you'll need to check the manual verify the correct IC convergence chips and resistors, the manual link is below as well... usally the IC's are STK392-120's or 150's and the resistors are 6.8 ohm 12 of then...

anyway read the general post below it will get you headed in the right direction.

51MP392H/17

Actually I have this TV and you need 2 Convergence IC's STK392-120's (120's and 150's will work) of course order 2 of the same type I'm using replacement 150's they allow for a little higher heat and were cheaper ALSO you need to replace the 12 resistors with 6.8 ohm metal film resistors, make sure they are metal film! don’t skimp out here I did and then they blew and fried my IC's and I had to replace everything again!

Great reference link that I posted
pictures on, check out page 3
http://www.techlore.com/forum/thread/16736/Magnavox-51MP392H-17-51-quot--TV-has-double-vision/

Where I got my parts that worked:
Suburban Electronics
http://www.suburban-elect.com/
Manual Library you should find all you need here:
http://www.techlore.com/group/2/list_downloads



What you need:
(2) STK392-120 OR STK392-150 IC
chips
(12) 6.8 Ohm Metal Film resistors
set of star screw drivers
15 watt pencil solder pencil, DO NOT use a high watt iron you will fry the surface mounted item.
good leaded solder, and flux

Nov 11, 2008 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

Philips rear projection tv-wont turn on


Sounds like your Convergence chips failed, were your red/blue/green colors slowly seperating or was the picture starting to curve on the top or bottom or both? if so see below general post.
Also what model # is your TV and what size?

51MP392H/17
Actually I have this TV and you need 2 Convergence IC's STK392-120's (120's and 150's will work) of course order 2 of the same type I'm using replacement 150's they allow for a little higher heat and were cheaper ALSO you need to replace the 12 resistors with 6.8 ohm metal film resistors, make sure they are metal film! don’t skimp out here I did and then they blew and fried my IC's and I had to replace everything again!

Great reference link that I posted pictures on, check out page 3
http://www.techlore.com/forum/thread/16736/Magnavox-51MP392H-17-51-quot--TV-has-double-vision/

Where I got all my parts that worked:
Suburban Electronics http://www.suburban-elect.com/

Manual Library you should find all you need here:
http://www.techlore.com/group/2/list_downloads



What you need:
(2) STK392-120 OR STK392-150 IC chips
(12) 6.8 Ohm Metal Film resistors
set of star screw drivers
15 watt pencil solder pencil, DO NOT use a high watt iron you will fry the surface mounted item.
good leaded solder, and flux


BTW if you don’t plan on trying this and are going to throw out the TV, I still need a IC convergence board for a 51MP392H/17 TV I'm fixing, I'm willing to pay S/H and buy your IC board that’s not been tampered with. Edwinkraus@hotmail.com

Nov 02, 2008 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

I have a magnavox 51mp392h rear projection tv and im having problems with the convergance


51MP392H/17

Actually I have this TV and you need 2 Convergence IC's STK392-120's (120's and 150's will work) of course order 2 of the same type I'm using replacement 150's they allow for a little higher heat and were cheaper ALSO you need to replace the 12 resistors with 6.8 ohm metal film resistors, make sure they are metal film! don’t skimp out here I did and then they blew and fried my IC's and I had to replace everything again!

Great reference link that I posted
pictures on, check out page 3
http://www.techlore.com/forum/thread/16736/Magnavox-51MP392H-17-51-quot--TV-has-double-vision/

Where I got my parts that worked:
Suburban Electronics
http://www.suburban-elect.com/
Manual Library you should find all you need here:
http://www.techlore.com/group/2/list_downloads



What you need:
(2) STK392-120 OR STK392-150 IC
chips
(12) 6.8 Ohm Metal Film resistors
set of star screw drivers
15 watt pencil solder pencil, DO NOT use a high watt iron you will fry the surface mounted item.
good leaded solder, and flux


BTW if you don’t plan on trying this and are going to throw out the TV, I still need a IC convergence board for a 51MP392H/17 TV I'm fixing, I'm willing to pay S/H and buy your IC board that’s not been tampered with.
Edwinkraus@hotmail.com

Oct 05, 2008 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

60" Rear Projection TV


sounds like a convergence chip problem...

here is my general post for the 51 inch you'll have to look at the link for the manual and check to see if you have the STK392-120 chips or somthing bigger in the 60"


51MP392H/17
you need 2 Convergence IC's STK392-120's (120's and 150's will work) of course order 2 of the same type I'm using replacement 150's they allow for a little higher heat and were cheaper ALSO you need to replace the 12 resistors with 6.8 ohm metal film resistors, make sure they are metal film! don’t skimp out here I did and then they blew and fried my IC's and I had to replace everything again!

Great reference link that I posted
pictures on, check out page 3
http://www.techlore.com/forum/thread/16736/Magnavox-51MP392H-17-51-quot--TV-has-double-vision/

Where I got my parts that worked:
Suburban Electronics
http://www.suburban-elect.com/
Manual Library you should find all you need here:
http://www.techlore.com/group/2/list_downloads



What you need:
(2) STK392-120 OR STK392-150 IC
chips
(12) 6.8 Ohm Metal Film resistors
set of star screw drivers
15 watt pencil solder pencil, DO NOT use a high watt iron you will fry the surface mounted item.
good leaded solder, and flux

Aug 21, 2008 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

SMALL CRACK IN CENTER OF PROTECTIVE SCREEN SHIELD ON TV


according to service information on this model there is no protective screen inventoried

Aug 11, 2008 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

Magnavox 51MP392H/17


No, if the Red doesnt adjust with the remote, You will need to replace both STK392-120 Convergence ICs. Its a fairly easy job if you have basic soldering skills, and you will also need about four 6.8 ohm 1 watt resistors for your model. You can get replacement ICs and resistors at the following link and they provide free instalation instructions with pictures. Heres the link.
http://servicemanuals.vstore.ca/

Jun 16, 2008 | Televison & Video

1 Answer

51 magnavox projection tv-color mixing wrong


The are controls on the inside of the tv above the circuit boards for focus and to turn up intensity of the projector lamps (red, green, and blu). If you turn it up too far all three projector lamps kick off. If this happens, power off the set and turn down the lamp that you turned up. Power it back on and slowly turn the projector lamp up until the picture looks OK. You have to take off the panel on back of set to get to the controls.

Nov 19, 2007 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

51" Magnavox projection TV


same with mine. Two things that they have to install and they need the whole tv there to fix it and run it for a week. Cost 500.00!!!

Aug 20, 2007 | Philips Magnavox 51MP392H Rear Projection...

Not finding what you are looking for?
Philips Magnavox 51MP392H Rear Projection Television Logo

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69845 Answers

matt martin
matt martin

Level 3 Expert

1198 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...