Question about Kenwood Audio & Video Receivers

1 Answer

Kenwood VR-2090 was overloaded and no longer works. Can i personally repair the unit?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Kenwood Master
  • 1,550 Answers

I don't think so because the audio amplifier IC of the device are damaged you need to send it to a repair center.Good luck

Posted on Jul 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kenwood Auto video surround receiver DR / 409 how to reset it


PDF]KRF-V8030D VR-409 - Kenwood

manual.kenwood.com/files/B60-4593-00.pdf
VR-409. INSTRUCTION MANUAL. KENWOOD CORPORATION. B60-4593-00 (EN) ...on the country and sales area. AUDIO VIDEO SURROUND RECEIVER ...

Kenwood VR-409 Manuals

www.manualslib.com > Brands > Kenwood Manuals > Stereo Receiver
View online or download Kenwood VR-409 Instruction Manual. ... Kenwood Instruction Manual Audio Video Surround Receiver KRF-V8030D VR-409.

Kenwood VR-409 Receiver Repair Questions, Solutions ...

www.fixya.com > Forum > Audio & Video Receivers > Kenwood
Recent Kenwood VR-409 Receiver questions, problems & answers. Free expert DIY tips, support, troubleshooting help & repair advice for all Audio & Video ...

Kenwood VR-409 PDF Owner's Manual Download & Preview

www.manualguru.com > Kenwood Manuals > VR-409

Feb 03, 2016 | Kenwood Audio & Video Receivers

1 Answer

Prologic on Kenwood VR-407 not working


plug front speakers into the a side

May 31, 2009 | Kenwood VR-407 Receiver

1 Answer

I have a kenwood vr 406 and a kenwood rcr0609 remote. After some time, the remote stopped working , so we got a new remote. This worked about a day. The remote itself seems to be working, because I can...


Kenwood receivers recently have a commonly known problem with its receiving IR diode within the receiver, to fix this you will have to re-solder the connection on the receiver panel within the faceplate of your kenwood receiver.

Instructions to fix it are at the following link if you are willing to open up your receiver and repair it. lots of people have reported this fix as successful so it is widely believed to be a design flaw in the VR line-up of receivers as it has occured in all the VR families so far.

good luck.

Jan 20, 2009 | Kenwood VR-406 Receiver

3 Answers

Remote not working


u try new bateries alkiline ones if that aint it we can get u new remote at www.remotewarehouse.com ok

Jan 27, 2008 | Kenwood 1080VR Receiver

1 Answer

No receiver display...no audio out


cheak displeys wires pluged in tight does sterio get hot then u see it go off

Jan 23, 2008 | Kenwood VR-2090 Receiver

1 Answer

Kenwood VR-207 Receiver


You will first need to check the remote control for the unit. Point the remote at a video camera and see if you see the remote light up. If it does try first to UNPLUG the unit for at least a couple of hours. If that as well does not work, you will need to have the unit serviced, as it may have a bad remote sensor on the front board or the microprocessor is No good. Depending on how old this unit is, it may not be worth repairing. Good Luck

Mar 21, 2007 | Kenwood VR-207 Receiver

2 Answers

Shutting itself down


Its usually not a fault that you will see unless somethings burnt up. This is solid state electronics and you dont see this stuff go bad. But in the meantime try disconnecting the speakers and see if it still goes into shutdown and at the same time have a dc multimeter attached to the speaker outputs. If the unit comes on and you dont see any DC at all or very very little B+ on both speaker terminal sets then you may have a defective speaker. If you do see dc then thats why the protections comming on so you dont blow out your speakers. If you dont have any equipment or dont have any electronics experience I would then take the unit to a repair person for an estimate. Good Luck

May 06, 2006 | Kenwood VR-707 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

ask_not

Level 1 Expert

28 Answers

Fbcgilly

Level 1 Expert

13 Answers

Are you a Kenwood Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...